answersLogoWhite

0

ABS brakes are not spongy. If you have spongy brakes the reason is that there is air in the system. You need to have your brakes bled.

User Avatar

Wiki User

13y ago

What else can I help you with?

Related Questions

Can spongy brakes be caused by problem with ABS Controller?

Spongy brakes are caused by air in the brake lines.


Does a 1992 tracker have abs brakes?

yes they do have abs brakes


94 cavalier have abs brakes?

yes it does have abs brakes


Adjusting abs brakes 98 s-10?

You would adjust the brakes on a vehicle with abs brakes the same way you would adjust the brakes on a vehicle without abs brakes.


Where is the abs?

The ECU for the ABS brakes is attached to the Master cylinder for the brakes.


Where is the ABS ECU?

The ECU for the ABS brakes is attached to the Master cylinder for the brakes.


Does Mazda 626 have fuses for abs brakes?

No, a Mazda 626 does not have fuses for ABS brakes. In fact, many Mazda models do not have fuses for ABS brakes.


How do you replace abs brakes on 2002 Chevy s10?

You replace the brakes on an ABS S10 the same way you replace brakes on a non ABS S10.


How do you tell if a 1996 Honda Civic Lx has ABS?

Slam on your brakes. If your brakes lock up, then you do not have ABS. If your brakes do not lock up and you hear a knocking type of noise from your brakes, then you have ABS.


How to operate abs brakes?

Operating abs brakes are easy. The anit-breaks are there for hen your other brakes go out.


How do you bleed abs brakes on a 1998 Chevy truck?

Having ABS does not change how you bleed the brakes. Bleed them as you would if it did not have ABS.


Why are my brakes still spongy after bleeding them?

There are several reasons why your brakes may still feel spongy after bleeding them. Some possible causes include air still being trapped in the brake lines, a leak in the brake system, or worn out brake components. It is recommended to have a professional mechanic inspect and diagnose the issue to ensure your brakes are working properly and safely.

Trending Questions
Will a 1980 305 stock intake manifold fit a 1980 350 motor? Where would one shop for G6 accessories? What are the state requirements for motorcycle turn signals in Pa? The manual for my MTD 33 13 HP Yardman Snowblower says to remove two bolts etc. to separate the auger housing from the frame assembly to replace the auger belt but they won't separate. Help? What do warning lights mean in Toyota RAV4? What is the azimuth hole on your cassette deck used for? How do you replace rear speaker on 2002 Lexus es 300? Would the Ac compressor and power steering pump are controlled by the same belt? Do inner tie rods cause shaking of the steering wheel if they are bad? What does mil-prf-23699 stand for? When driving a vehicle equipped with ABS brakes what is the best way to stop in an emergency? Steering wheel shakes when braking at high speed after hitting right tire on a curb also car pulls to the left when i let go of the steering wheel? 3.8 L No codes run's rough rpm's fluctuate between 670-820 Plugswires new Replaced the Crankshaft sensor but still same issue If placed in Drivereverse and let go the break car dies Starts up again? How do you replace the clutch pedal position switch on a1996 dodge Dakota? What is the firing order for a 1985 Ford truck 460 engine? Where is the fuel filter on a 1988 454 engine? How do you make a 305 engine run cooler in a 86 trans am? What is the firing order for the 2002 town and country 3.8? What is the timing gear position on a 1989 Mercury Tracer? Where is the indicator fuse in a 1992 suzuki vitara?