0
The end pipe attached to a muffler is commonly referred to as the "tailpipe." It directs exhaust gases away from the vehicle and can influence the sound and emissions of the exhaust system. Tailpipes come in various shapes and sizes, often designed for aesthetic purposes as well as functionality.
What else can I help you with?
What will happen if you cut your exhaust pipe off but leave the muffler on?
If you were to cut off your exhaust pipe the muffler would come off with it, sence it is attached to the very end... I would be alot louder, it might hurt your MPG rating....
Side and a b side stamp on a muffler which side is the tailpipe?
I would say B is the tail pipe end.
How do you put a straight pipe on a dirt bike?
cutt off the muffler, the big oval thing near the end of the pipe then buy a metal pipe and cut to the right length if needed. then weld it onto the pipe that is cut
How is muffler use in sentence?
The muffler is at the end of the exhaust pipe and reduces the sound emitted from it. An example of a sentence using the word "muffler" is "The mechanic had to replace the muffler and a section of the exhaust. "
Where is the Location of 1991 firebird 305 v8 OXYGEN sensor?
It is in the exhaust pipe system. start looking in the exhaust system, starting up by the exhaust manifolds and work your way towards the muffler. There will not be any after the muffler. It is about 3 inches long and screewed into the exhaust pipe with a electric wire on the end of it.
Where is the oxygen sensor located on a 2000 Dodge Durango?
It is located on the muffler by the moter and looks like a sparkplug with wire attached at the end. To be specific, my 2000 Durango has 1 upstream oxygen sensor and 1 downstream oxygen sensor. Both are located on the exhaust pipe. The upstream is between the engine and catalytic converter. The downstream is located between the catalytic converter and muffler. - Mick
Where is the muffler on a 1985 Mazda rx7?
its the big can that's closest to the end of the exhaust pipe. the one about halfway through is the catalytic converter, and the things in front of that are preconverters
What happends if the a b is reversed on a muffler?
You end up with a b a muffler.
How to change a muffler on Chevy S-10?
First off, crawl under the truck and see if your present muffler is welded on or clamped on. If it's welded on you will need to get an exhaust cutting tool from like Autozone and cut the old muffler off BUT before you do, get your new muffler and measure how far the inlet neck is and outlet neck is on the new muffler and this will tell you how far to cut. You could hold the new muffler up to the exhasut and mark how far from the muffler you need to cut. This is assumign you are replacing the bad muffler with a new one of the same size. Now there is an inlet pipe and and out let pipe on the muffler. You will also need to have the right size clamps. Pu tone clamp on the exhaust pipe going to the engine, then push the exhaust pipe into the inlet end of the muffler and slide the clamp down and snug it up but do not tighten it. Put the other clamp on the exhaust pipe towrd the rear of the truck, push the exhasut ipe into the outlet end of the muffler and then slide the clamp down onto the joint and snug up. if everythign aligns right, then tighten the clamps. Sometimes if you overtighten the clamps you will have exhaust leaks. If you cannot get the joints to seal, you may need to get your system welded. If you exhaust is leak free then you are done. After a few hot and cold cycles you may just want to crawl back under and check the bolts on the clamps just in case they came loose from the heat and cold cycles.
Where are the locations of the o2cesers in a 2000 Chevy 1500?
They are 3 to 4 inches long with an electric wire in the end of them and they are screewed into the exhaust pipe / pipes. There is 4 of them on that engine and there will not be any after the muffler.
What is the vacuum pipe attached to on the front clip on your 82 vandura I have the pipe connected to a device that is electrical at one end and not connected at the carb end..my bacfire?
If 4 pipes of equal length measure 44 feet when they're connected together, how long is each pipe?
Where are o2 sensors located on 1997 Chevy silverado?
Thay are screewed into the exhaust pipe system. There will not be any after the muffler. Thay are about 4 inches long with an electrical wire hooked to the end of them.
