0
What else can I help you with?
How do you change generator's belt?
Just release the bolt that adjust the position of the generator, this will loose the old belt also, take the old one out and place the new one, ajust tha tension and tight the bolt.
How much to replace a generator belt on a 2003 volkswagen jetta?
A generator belt on a 2003 Volkswagen Jetta costs approximately fifteen dollars to replace for the part only. Labor pricing would increase the total cost.
What are the Symptoms of a broken serpentine belt?
All the services driven by this one belt fail at the same time. Generator, pump, etc.
Where is the Diagram for 2002 Toyota solara serpentine belt?
The 2002 Toyota Solara does not have a "serpentine" belt that turns all of the pulleys. It has one belt that runs the power steering and a second "generator drive" belt.
How does the generator turn quickly enough to transform mechanical energy in electricity?
v belt
Why does the Generator Lite come on?
Usually because your fan belt is too loose, or it broke.
How do you remove drive belt from Toyota Echo?
It's pretty easy. Locate the generator/alternator which is the top from pulley that the drive belt touches. On the bottom of the generator is a 12mm bolt, loosen this (but there is no need to take out off, just loosen it). There is a slider bracket on top of the generator with another bolt, loosen that one as well. I strongly recommend spraying penetrating oil (I like deep creep but there are many that will work fine) on the bolts and all along the slider area. Now that its loose you can push the generator back, taking the tension off the drive belt, now you can easily remove the belt. When you are ready to re-install, just pry the generator forward again until the belt is tight, you can use a pry bar, you really need two people for this, one to pull it back, and the other to tighten the slider bracket bolt down while the belt is tight. If you are putting on a new belt, you may want to check and re-tighten it after a break in period (couple days of driving). Don't forget to re-tighten the lower bolt on the generator after you have locked down the top bolt.
How do you replace the alternator on an 04 dodge ram?
Its real easy. 1st Get a breaker bar (an extremely long ratchet like a torque wrench). Locate the idler pulley and the size the bolt for a socket that holds the idler pulley on the idler arm (Hint: The idler pulley is just a pulley connected to a springloaded assembly attached to your enginge block putting pressure on the serpentine belt so it is tight around all the component pulleys (alternator, power steering, crankshaft, etc. pulleys).Using the correct size socket attached to the breaker bar for leverage put the socket onto the bolt head and pull or push the bolt head of the idler puller either forward or backward (which ever way causes the tension arm to move thus moving the idler pulley so that pressure is removed from the serpentine belt). Now remove the serpentine belt. A serpentine belt diagram should be located somewhere on a decal near the radiator or some other location under the hood...if not, before you remove the serpentine belt, map out the serpentines route with pen and paper so you can put the new one on the same exact way. When putting on the new belt you will again have to position the idler pulley usig the breaker bar and socket such that you can stretch the new belt over all the component pulleys...please note...you will only have one free hand when your doing this, so make it count and be patient...you will succeed. Good luck ...maxvolt1@verizon.net
How do you fix the generator warning light?
the generator warning light - it indicates malfunction in charging system. The light should go off once the engines started, if it comes on while driving, the generator drive belt and the charging system needs checked.
How a van der graaf generator works?
A Van der Graaf generator is an electrostatic generator which uses a moving belt to accumulate very high amounts of electrical charge on a hollow metal globe to the top of the stand. It is also the name of a metal band.
What does vande graff generator do?
A Van de Graaff generator is a device that is used to generate high voltages of static electricity. It consists of a large globe on top of a stand, with a belt mechanism that helps accumulate electric charge on the globe. This static electricity can be used for various experiments and demonstrations in physics.
Explain how a Van de Graaff generator builds up a static charge.?
A Van de Graaff generator uses a motor to transfer positive charge from a grounded metal sphere to a rubber belt continuously. The charge builds up on the metal sphere as the belt moves, creating a high voltage difference between the sphere and the belt due to the continuous transfer of charge.
