answersLogoWhite

0

It is there as a "pass through". This comes in handy if your deck only has one set of RCA outputs. It enables you to "daisy chain" multiple amps together. You would run the RCA cables from the deck to amp #1's input, then use a another cable from the output on amp #1 to the input on amp #2.

User Avatar

Wiki User

16y ago

What else can I help you with?

Related Questions

Can you run a car amp output into another car amp?

I have, I have even used the output for the input of the same amp, so that you only run one RCA cable to the amp, then run the output back to the other input, and it runs 4 channels.. :o)


How can you tell if the head unit output signal is to strong for the amp?

if the head unit can produce sound to your speakers without the amp you have high level output from head unit if your amp only accepts low level input (rca) plugs you must buy a high to low level converter which take speaker high output and reduces it to low ( rca) output and then go to your amp converter is under 20 bucks but most new amp accept hi and low level feed


Sony Xplod XM-1652z 1000watt amp for my car and it has a high power input spot what does this do i have the connector but what do you connect to it and what does it do?

It's so you can use your stereo speaker output wires to the amp without having to use RCA cables It should say High Level Input and you use it or RCA cables. Not both. If you plan on using the amp to power subs use RCAs. If you plan on running mids and highs you can use what you like. If your stereo has front and/or rear RCA outputs as well as sub output it's your call


How do you connect your speakers to your aftermarket amp in a jeep charokee amp?

The RCA's from the amp will be arn to the CD player, then you need to connect the speaker's wire to the output + and - of the amp, this will cause the amp to have musical power from your radio, and the speakers to have the power from the amp..-Shocker


How do you run an amplifier off a normal car radio?

Normal car radio is no different than aftermarket. Determine the output wires on the radio, take them into the amp and the output from the amp back to the wires going to the speakers. Normal car speakers are not going to take the output of the amp if you raise it much.


How can I connect a connect amp to an audio interface?

To connect a Connect Amp to an audio interface, you can use a standard RCA cable. Simply plug one end of the RCA cable into the audio output of the Connect Amp and the other end into the audio input of the audio interface. This will allow you to play music from the Connect Amp through the audio interface.


How do you install amp to a durabrand db1215 car stereo?

due to fact there are no rca outputs you must purchase a line level converter, which has RCA type jacks.


What kind of Car CD/MP3 player has the best audio output?

RCA or Alpine hd


How to install a amp and subwoofers in a 2001 Oldsmobile aurora?

you would just install them like you would on a normal car, but I'm assuming you are using the stock head unit which doesn't have RCA outputs, so you will need to buy a line output converter to run the RCA cables from the head unit to the subs


Can you attach your Mp3 Flash drive to a Car Amplifier with out using Car Stereo?

I believe you can if you can find a cord that would have RCA jacks on the end to plug into your amp


How do you put a subwoofer in your car?

You have to run the powers and grounds for the amp, do not forget to set up the remote wire either. then you will need to connect the amp to the CD player auxillary with the RCA's, then you just wire your sub to the amp.-Shocker


How do you install a amp to a almera?

To install an amp in an Almera, you will need to connect the amp's power wire to the car's battery, ground the amp to a metal part of the car's chassis, and connect the amp's remote wire to a source that turns on when the car is started. You will also need to run RCA cables from the head unit to the amp for signal input, as well as speaker wires to connect the amp to the car speakers. It's recommended to consult a professional for the installation to ensure safety and proper functionality.