0
The part number would be assigned by any number of equipment manufacturers that have used thes pumps, for instance the Bolens part number for a 5120h is 1745147. The model number for an Eaton 11 is stamped on it, this number begins with 1100 this identifys it as a model 11 and the next three numbers are the specific unit configuration. there are at least a dozen different configurations. Eaton may be able to provide you with a new pump or rebuild kit provided you have the model and configuration number
What else can I help you with?
What kind of oil do you use in your hydrostatic trans for my 1142 simplicity lawn mower?
Hi, your Eaton model 6 hydrostatic transmission requires straight 30 weight oil according to the manual.
Where is the hydrostatic drive shaft on a Model 2320 John Deere tractor?
On a Model 2320 John Deere tractor, the hydrostatic drive shaft is located between the engine and the hydrostatic transmission. It typically runs along the tractor's chassis and connects to the hydrostatic pump, allowing power transfer from the engine to the transmission for driving the tractor. For specific maintenance or troubleshooting, consulting the operator's manual or a service guide is recommended.
Where can you find parts for a eaton 1100 045 transmission?
You can find parts for an Eaton 1100 045 transmission at various sources, including authorized Eaton dealers and distributors. Online platforms like eBay, Amazon, and specialized truck parts websites may also offer parts. Additionally, local automotive or heavy-duty truck repair shops might have access to Eaton transmission components or can help order them for you. Always ensure that you verify the compatibility of parts with your specific transmission model.
What kind of oil do you use in your hydrostatic transmission for my 4212 simplicity lawn mower?
I had the same problem When I bought my mower I put premium hydraulic oil in it. It would move until it warmed up. then would slip. I thought I was going to have to buy a new drive. I finally got in touch with an engineer at Eaton Hydrostatic, the place that makes the hydro units, and he asked me what oil I was using. I told him premium hydraulic oil. He said "No wonder. You need to use 30 weight motor oil." I haven't had any trouble since. My mower is a 4211 Hydro, with an Eaton Model 6 Hydro unit that is attached to a peerless drive unit. So if your unit is an Eaton Model 6 or 7, use 30 weight motor oil in it.
Where is the neutral safety switch located on a 2002 Kenworth?
Depends on model and transmission. On most KW trucks, there isn't one. If you have an automatic, then it depends on your transmission, e.g., Allison, Eaton Smart Shift, Meritor, etc.
Where is the transmission model number located in a 1971 Chevelle?
on the side of the transmission itself.
What type transmission fluid for 1994 freightliner?
Knowing the transmission type is much more important than knowing the model of truck. If it's an Eaton Fuller, they recommend 50w synthetic or 70-80w mineral oil.
Where is the transmission model number located on a 1997 jetta manual transmission?
Next to the starter
How do you find out what make and model transmission you have in your 2000 Chevy S-10 2.2L 5-speed?
Look on the side of the transmission housing. There will be a manufacturer tag on either the right or left side of the transmission. That will give you the manufacturer and serial number/model number of your transmission
Transmission on a 2005 Ford Focus?
I am not sure what the question is, the transmission model number for a 2005 Focus is a 4F27E
How do you release the hydrostatic on JD lx188?
To release the hydrostatic drive on a John Deere LX188, locate the hydrostatic release lever, which is typically found near the rear of the mower, near the transmission. Pull the lever outward or push it down to disengage the hydrostatic drive, allowing the mower to roll freely. Make sure to return the lever to its original position before operating the mower again to ensure normal driving functionality. Always refer to the operator's manual for specific instructions related to your model.
How do you downshift an Eaton shifter?
Depends on what model it is. Eaton makes both synchromesh and unsynchronized transmissions. The synchromesh transmissions (6 and 7 speed) shift like a regular car or light truck transmission.. push in the clutch, downshift. Unsynchronized transmissions, you take the transmission out of gear, rev the engine up the appropriate RPMs, then push it into the next gear down. This requires you to hit the RPMs right.
