What is the rms on a sony 1000w amp?

What size amp do you need for 6 and a half Sony speakers that has 190 Watt peak power and 40 rms and Sony 6 by 9 speakers that has 300 Watt peak power and 60 rms?

200 RMS 4 channel or 2 channel so u know add the rms of the speakers to find the amp rms needed

If you have two 400 watts rms subs 1200 max kenwood kfc-w3011 what power amp should you get?

1000W Kenwood KAC-7204 2/1

What kind of amp do you need if you have one 10 inch sub 300 RMS Sony Xplod and all your speakers together add up to 350 RMS Kicker Speakers?

kicker ZX650.4 for sure

How many watts does a sony xm752x amp put out?

The Sony XM752X amplifier can output up to 280 watts RMS per channel at 4 ohms, or 380 watts RMS per channel at 2 ohms, when both channels are driven with a 20Hz - 20kHz signal.

Is 1 farad capacitor enough for 1000 watts pioneer sub woofer?

It depends on the power rating of the amplifier. The rule of thumb is often said to be 1000 RMS watts per farad. RMS watts is basically the average output of your amp/subwoofer. The power ratings most often given by manufacturers are Peak Watts, ie. how much power the amp/sub can take before breaking down. The RMS wattage is often about half of your Peak rating. So, given that you are running your 1000w Peak Pioneer subwoofer on a 1000w Peak amplifier, and given that both of them are 500w RMS, yes, a 1 farad capacitor would give the amplifier enough juice to run the sub.

I have a nitro bmw483 1000w 4channel amp i do not know where to put the RCA cables i have the power remote and ground cables in and my amp has power now how do I get sound with the RCA cables?

I do not have the knowledge on nitro bmw483 1000w 4channel amp hence cannot be in a position to help you in your question.

What will happen if you hook up a system and the amp rms is lower than the sub rms?

you could possibly kill your amp. because the subs are asking for a certain amount of power and your amp cant give the power. but typically the amp will push all its power avalible to the sub and you should be fine. but for the optimum sound system the amp rms should be the same or close to the sub rms.

Can you power a 1300 watt sub with a 1500 watt amp?

Yes, are we talking rms or max? If its rms you will have no problem. well the amp is a 1500 watt max but 350wx1 rms in 4 ohm

How should I wire two 12 inch Power Acoustik Fubar 1800w 800rms dvc 4 ohm subwoofers in a dual chamber sealed box to a American Bass 1000xd amp How can I get max performance with this setup?

It's a borderline setup even in a best case scenario. I couldn't find a lot of specifics on the amp. It is a 1000W rated amp, but I couldn't find if that is peak or RMS. I also couldn't find out at what impedance that 1000W is being generated. Even if we assume the "best case" scenario of the amp being 1000W RMS @ 4ohms. That means it SHOULD be capable of 2000W @ 2ohms. If you set those speakers up in parallel they will require 1600W @ 2 ohms. Admittedly, initially that looks good, the amp has more power than the speakers are demanding - but not by much. My rule of thumb is that an amp should be AT LEAST 30% more powerful than the speaker(s) it's connected to. In this setup it is only 25% more powerful, and that's the BEST CASE scenario. IF that 1000W rating is PEAK, then it's RMS is approximately 500W @ 4 ohms (and therefore about 1000W @ 2 ohms). In a parallel setup, those speakers will need 1600W @ 2 ohms. In that configuration you've UNDERPOWERED the speakers by over 30%. That amp will put out so much distortion it'll kill those speakers in no time. In conclusion, I wouldn't personally recommend that equipment pairing to a customer. It's too borderline for my liking, it's safety margin isn't large enough. On the other hand, many installers feel quite confident recommending an equal pairing. "100W of speaker needs 100W of amp". Since you exceed that by 25% in the best case scenario, many would say it's fine. You'll have to find out the RMS and impedance figures and go from there.

What amplifier do you recommend for 2 subs I have 2 Sony Subws both at 1300W each. Most amps only supply a Max of 1000W. Does it mean that I need a amp that can handle 2600W?

Since you didn't specify if that 1300W is Peak or RMS, or at what impedence(ohms),I'm going to assume that the 1300W is a Peak rating. This means that(more than likely) the RMS rating will be around 650W. I'm also going to assume that is at 4 ohms.If you intend to run these subs in parallel, you will need an amp capable of supplying AT LEAST 1300W RMS into a 2 ohm load.If you intend to run these subs in series, you will need an amp capable of supplying AT LEAST 1300W RMS into an 8 ohm load.Also,my basic rule of thumb is that your amp should be about 1/3 more powerful than your sub(s) require. So, you should actually be looking for an amp in the 1800W range.You should be able to find an amp to match these requirements fairly easily, there are quite a number of amps out there that well exceed 1800W @ 2 ohms.I'm not saying that they come cheaply - be prepared for prices in at least the $900-$1000 range. :-(

How do you find out the rms on a amp?

you stick your tongue in the outlet and however many seconds you are shocked is how many rms are there

Okay so im buying two Kenwood 12 4-Ohm SingleVoice Subwoofer they have 400w rms each I kno amp rms has to equal subs rms Now my question is what type of amp am i looking for what about ohms?

Get a 1600 watt amp. The best amps are Rockford Fosgates.