0

Subjects>Auto>Auto Parts

What is the valve clearance on a Briggs and Stratton 16 HP OHV engine?

Anonymous

∙ 15y ago

Updated: 10/23/2022

0.004" would be correct. See the YouTube link attached below for the procedure.

Wiki User

∙ 15y ago

What else can I help you with?

Related Questions

What is the valve clearance on a Briggs and Stratton 16.5 HP OHV engine?

0.004 - 0.006"

What is the valve clearance on a Briggs and stratton 20 hp v twin engine?

cawl sistem

What is the Valve clearance for 21 hp Briggs and stratton?

.004-.006

What is valve clearance for Briggs and stratton 406777?

The valve clearance for a Briggs and Stratton 406777 engine is typically set to 0.004 to 0.006 inches for both the intake and exhaust valves when the engine is at top dead center on the compression stroke. It's important to adjust the clearance when the engine is cold to ensure accurate measurements. Always refer to the specific service manual for your engine model for the most precise information.

What is the valve clearance on a Briggs and stratton 14hp vanguard?

005 in 007 ex

What is the valve cearance on a Briggs and stratton 21 hp ohv engine?

The valve clearance on a Briggs and Stratton 21 HP OHV engine is typically set to 0.005 inches for both the intake and exhaust valves when the engine is cold. It's important to check the specific model's service manual for any variations or specific adjustments. Proper valve clearance ensures optimal engine performance and longevity.

What is the valve clearance on a Briggs and stratton 10hp eng?

http://www4.briggsandstratton.com/miscpdfs/RNT/Engine%20Specifications%20Chart_ms3992.pdf

What is valve clearance for 18 hp Briggs and stratton?

.003 exhaust-.005 intake

What is the valve clearance on a 14.5 hp brigg's and stratton?

Briggs says on a cold engine, .005 on intake & .007 on exhaust. Wider on exhaust to ensure you don't burn a valve.

What should the valve clearance adjustment be for an 8 HP Briggs and Stratton engine?

For the aluminum the intake valve clearance is .005 to .007 inches. exhaust valve clearance is .007 to .009 inches. Cast iron is - intake valve is .007 to .009. inches exhaust valve is .017 to .019 inches

What settings do you use for a 21.5 hp Briggs and stratton push rods?

I assume valve clearance and it is 0.004".

Is the exhaust valve on 15.5 hp Briggs and stratton engine on top?

Yes

Trending Questions

How do I change oil and filter on 2007 Avalon? What if you put diesel in a gas engine? How many miles per gallon for a g6? How much oil did America use in 2011? What does the ignition fuse look like for a 1978 Oldsmobile cutlass? How many liters of oil go in a vw engine? What do you call the part behind the rotor on a 2003 mustang behind the rotors. My mustang was on a jack when the jack dropped and the part was bent. I need to replace it but don't know what it is.? What is the firing order diagram for F350 460 motor? Why do your battery keep going down? Will a bad ecu cause no spark? What can carburetor cleaner do to a fuel injected engine? Can you have a turbocharger without an intercooler? What is the synomyn for tread? When did the countuires need most of oil? Does the 1998 INFINITI Q45 timing belt or Chain? Where is the fuel filter located on a 1999 Dodge Durango 4x4? Why do the specs for the BMS Tomahawk 400 list 15W40SG as engine oil and 10W40 as lubrication oil? What causes a hub to go bad? How do you change alternator in Volvo s40? How many seconds does it take after exposure to headlight glare for the pupil to adapt once again to dark conditions?

Resources

Top Categories

Product

Company

Copyright ©2025 Answers.com. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Answers.