answersLogoWhite

0

Nicad batteries have sodium hydroxide electrolyte. Citric acid powder will neutralize it.

User Avatar

Wiki User

12y ago

What else can I help you with?

Related Questions

How much baking soda is needed to neutralize car battery acid?

No much, just sprinkle it on the spill.


How do you remove battery acid from trunk of car?

If it is spilled in the trunk, start by mixing baking soda with water and pouring it on the acid spill to neutralize it.


How do you neutralize a base spill?

Use an acid.


What effect will battery acid have on the rubber hoses in your car?

Sulfuric acid attacks and degrades Buna-N rubber. As to the possibility it can damage a rubber hose, I would not take any chances. Rinse all spilled electrolyte off the area you spill it on thoroughly. You can also pour some baking soda on the area to neutralize the acid.


What is the difference between a wet cell battery and a dry cell battery?

Dry cells use a damp paste electrolyte in a sealed housing so the electrolyte can not spill or leak from the cell and damage the equipment it powers. Wet cells use a liquid electrolyte that can spill and/or leak from the cell and severely damage the equipment it powers. Almost all early battery cells were wet cells with the electrolyte contained in either a glass beaker or glazed pottery crock. The user had to periodically add water to keep them from drying out and being damaged, also he had to be careful not to spill or crack the cell. Almost all modern cells are dry cells because they don't spill or leak and require no user maintenance. The main wet cell still used is the lead-acid battery used in car batteries (and some of these have the acid gelled to keep it from spilling or leaking). Dry cells have generally replaced wet cells because they are more practical.


A dry battery and a wet battery and ...?

To put simply a "dry" battery is one that does not have any electrolyte (acid)... as such a dry charged battery is one in which the plate/cells of the battery are fully charged but will need to add the acid at the end user side before the battery is activated.The Wet battery, is one that comes from the factory/production side fully charged and ready to use (with the acid inside).Wrong. Both wet and dry batteries contain an electrolyte, but in the dry battery the electrolyte is absorbed into a solid material forming a damp paste. The dry battery is not really dry, its actually damp. The important difference is that the liquid electrolyte in a wet battery can spill and the damp paste electrolyte in the dry battery can't.Lead-acid batteries are commonly shipped and sold without the electrolyte as this simplifies shipment and extends shelf life in the store. But they are still wet batteries as they cannot function until the electrolyte is added. True dry batteries need nothing added to function.


How to neutralize sulfuric acid spills in a lake?

To neutralize a sulfuric acid spill in a lake, you can gradually add a base such as sodium bicarbonate (baking soda) or calcium carbonate (lime) to the affected area. This will help to neutralize the acidity and reduce the potential harm to aquatic organisms in the lake. It is important to follow proper safety procedures and guidelines when handling and neutralizing the spill.


If spilling occurs what do you do?

You neutralize base spill with vinegar before attempting to wipe up.


What is the dry battery?

A dry-charged battery is a conventional non-sealed wet-cell battery (this is almost always a rechargeable type). Normally, this battery type is wet-charged, meaning that the battery is filled with electrolyte at the factory, charged, and then shipped with the electrolyte in the battery. However, since the battery is not sealed, the electrolyte (either a strong acid or alkali) can spill out, which can be both a health and environmental hazard. The battery will also self-discharge at its normal rate during shipment and storage. Dry-charging is a way to minimize these problems. Like a wet-charged battery, a dry-charged battery is filled with electrolyte at the factory and charged. However, the electrolyte is then removed from the battery. The battery is then washed out, dried out, and sealed. The battery may also be filled with an inert gas to minimize reaction of any remaining electrolyte, as in the U.S. military BB-451/U silver-zinc battery, which used a very strong alkaline electrolyte (40% potassium hydroxide). The sealed battery is shipped and stored separately from the electrolyte. Because the electrolyte is in a sealed container, chances of spillage are reduced. The sealed battery will also self-discharge at a lower rate than usual, so it should still have useful charge up to 18 months after manufacture if stored below +90 degrees Fahrenheit (+32 degrees Celsius). When the battery is needed, the electrolyte is CAREFULLY added back to the battery (eye protection and gloves must be worn and other precautions taken). The battery must be allowed to sit for some time afterwards so the electrolyte can soak around and through the battery's internal structures. The electrolyte temperature will rise and its specific gravity (SG) will drop during the soak. The manufacturer may recommend that the SG be measured after the soak time, and the measured value will have to be corrected for any difference between the actual electrolyte temperature and the temperature at which the reference SG was measured. After the soak time, a (very rare) nonrechargeable dry-charged battery is ready for use, and some rechargeable dry-charged batteries may also be ready for use (like the BB-451/U). However, dry-charged lead-acid batteries will almost always need a low top-off or trickle charge. Rolls Batteries prescribes 5% of the 8-hour or 20-hour charge rate, to be reduced if the electrolyte becomes too warm or too much gas bubbles out of it. If the electrolyte in a rechargeable battery becomes too warm before charging, the battery will first have to be cooled down or allowed to cool naturally.


How do you neutralize a hydrogen peroxide spill?

To neutralize a hydrogen peroxide spill, you can use a solution of water and sodium bisulfite or sodium thiosulfate. These chemicals help break down the hydrogen peroxide into water and oxygen, making it safer to clean up. Always wear appropriate protective gear and ensure proper ventilation when handling spills.


How do you neutralize hydrogen peroxide spill on carpet.?

To neutralize a hydrogen peroxide spill on carpet, first absorb as much of the liquid as possible with a clean cloth or paper towels. Then mix a solution of equal parts water and white vinegar and blot the area with this solution. Finally, rinse the area with water and blot dry.


Which of the following is the best choice to neutralize a spilled acid?

Baking soda is the best choice to neutralize a spilled acid. It reacts with the acid to form water and a salt, which helps to neutralize the acidic solution. Remember to wear proper protective gear and ventilate the area while cleaning up the spill.