0
What else can I help you with?
How do you change oil in transfer case on 1996 Toyota landcruiser?
firstly you need to undo the top (also the place where you re-fill) bung on the transfer case. then undo the bottom bung and allow the oil to drain. i would recommend flushing with 500mls of oil to clear any scum. re screw the bottom bung and fill with 1.3lts of the recommend oil of the brand you choose. as a rule you fill till the oil starts to weep from the fill bung.
Can you bung booce?
yes all you need is pretzel sticks. :)
How do you fill and change the gearbox oil in 2001 Toyota hilux?
THIS IS FOR A MANUAL ONLYHOW TO DRAIN THE OILThere is a bung plug (24mm bolt) on the bottom which is used to drain the oil, replace bung after draining the oil.HOW TO REPLACE OILThere is an identical 24mm bung on the left hand side, about half way along and about half way up the side.Remove the SIDE bung and pump oil in until it just starts to come back out the (SIDE) bung hole, then replace the side bung and your finished.IMPORTANT: Make sure the oil pump hose is all the way in the bung hole, they tend to have a long threaded hole and if the oil hose is not in properly the oil will come back out and you might mistake it for being full.Its also a good idea to know how much oil your gearbox is suppose to have, this can be found in owners manual. This will help make sure you have enough oil to do the job and make sure you replace enough oil.You will need an oil pump, i brought one from "Auto Barn" for $19
How do you get an airlock out of a drain?
You may need a soil stack to release the airlock!
How can I replace a pop-up tub drain?
To replace a pop-up tub drain, you will need to unscrew the old drain, remove it, and then install the new drain by following the manufacturer's instructions. Make sure to use the appropriate tools and sealants for a proper installation.
How can I remove the drain stopper from the tub?
To remove the drain stopper from the tub, you can usually twist it counterclockwise to unscrew it from the drain. If it's a push-pull stopper, you may need to lift it up and then turn it to release it from the drain.
How can I remove a pop-up drain stopper?
To remove a pop-up drain stopper, you typically need to unscrew the top cap or lift and twist it counterclockwise to release it from the drain. Then, you can pull out the stopper assembly from the drain.
How can I replace a pop-up bathtub drain?
To replace a pop-up bathtub drain, you will need to unscrew the old drain, remove it, and then install the new drain by following the manufacturer's instructions. Make sure to use the appropriate tools and sealants to ensure a proper fit and prevent leaks.
How to remove the sink drain stopper?
To remove the sink drain stopper, you typically need to unscrew the top cap or lift and twist the stopper to release it from the drain. You may need to use a screwdriver or pliers to help loosen it if it's stuck.
How do I go about replacing a tub drain lever?
To replace a tub drain lever, you will need to unscrew the old lever from the drain, remove it, and then install the new lever by screwing it into place. Make sure to follow the manufacturer's instructions and use the appropriate tools for the job.
How do you top gearbox oil on a citroen c5?
where is the bung on a citroen c5 gearbox need to top up on oil
What is the function of a rubber bung?
A rubber bung (also called rubber stopper) is used in the laboratories for test tubes, flasks (made of glass usually). Bungs also used by winery industry for the wine bottles. A bung must fill well as a stopper. The bungs are of many sizes. Rubber bung can have one or more hole(s) for plugging in tube depending on the specification of the procedures. In chemical laboratory, to prevent the liquid chemical leaks or escape the container, we need the rubber bung that fit tightly to the container's open, therefore, the dimension of the rubber bung is concerned. These are some of the sizes that are commonly seen in chemical laboratory
