0
What else can I help you with?
Where is the tension in the beam bridge?
bottom of the beam
What does the tension dial do on a sewing machine?
It changes how easily the top thread moves through the machine. You want the top thread and bottom thread to have equal tension so you won't get loops of thread on the bottom or top of your seam. If you get loops on the bottom, tighten your top tension; if you get loops on the top, loosen the top tension.
Why are your clio front fog lights not working?
If it is a mk1 try checking the fuse or the bulbs, my clio had the same problem. I checked the bulbs and the fillaments were fine but the bottom of the bulb had corroded away. The solution new bulbs!
Locations of compression and tension in footing rebars?
Compression and tension occur in opposite side of the footing relative to position. So, at a spread ftg or pile cap, the top reinforcing will be in tension and the bottom compression. At the midspan, between spread ftgs or pile caps, the tension will occur in the bottom and compression in the top. Rebar lap splices usually occur in the compression points, so bottom lap at spread ftgs and top at midspans. Also, details will typical have additional rebar at the points of maximum tension so at the top over supports and bottom at midspans. This though should be confirmed with the Engineer of Record on any project, as assumptions can change project to project. But this is the general concept.
How many junctions are checked to test the serviceability of a transistors?
Not sure what you are checking, but a transistor has two junctions. Think of a three layer cake with chocolate on the bottom layer, vanilla in the middle and chocolate on the top. The junctions are where the chocolate and vanilla meet.
How to fix the bottom of a chain link fence?
To fix the bottom of a chain link fence, you can start by digging a trench along the bottom of the fence line. Then, insert new tension wire or bottom rail and secure it in place with tension bands and bolts. Finally, backfill the trench with soil to secure the bottom of the fence.
What is the proper technique for checking transmission fluid?
Each vehicle can be different. Manuals tend to have fill plugs, where the fluid is set to the bottom of the hole with the engine off. Most automatics have dipsticks. It depends on the transmission if it is checked in park or neutral with the engine running.
Why does a dog scrape it's bottom along the ground?
To clean its bottom and to literally scratch its bottom. == ANSWER == This may be a sign of worms, please get your pet checked.
How do you take the tension off of the serpentine belt on a 1996 Chevy Corsica?
On my 94, the tension bar is between the passenger wheel well and the motor, towards the bottom. Use a wrench to lift the tension bar, and the belt should loosen up. On my 95 Corsica 2.2 4cyl, the tension pulley is DOWN and to the LEFT of the alternator pulley. The space in between the bolt on the pulley and the side of the engine compartment is to small for a socket. I used a box wrench and turned CLOCKWISE.
What is the magnitude of the tension in the string when the ball is at the bottom of the circle?
The magnitude of the tension in the string at the bottom of the circle is equal to the sum of the gravitational force acting on the ball and the centripetal force required to keep the ball moving in a circular path.
Why is the reinforcement bars place at bottom of the simple supported beam?
When a simply supported beam is subject to bending; the top of the beam will be subject to compression, and the bottom of the beam will be subject to tension (think about the bottom of the beam stretching as it bends i.e. tension). Concrete is strong in compression but weak in tension, so steel reinforcement is added to allow it to resist this tension and carry bending sufficiently. Note: bars are generally added to the compression side too but that's for another day.
What are the best practices for changing and maintaining the tension of guitar strings from top to bottom?
To change and maintain the tension of guitar strings from top to bottom, it is best to tune the strings gradually and evenly, starting from the thickest string (top) to the thinnest string (bottom). Use a tuner to ensure each string is at the correct pitch. Avoid sudden changes in tension to prevent damage to the guitar or strings. Regularly check and adjust the tension to keep the guitar in tune and prevent string breakage.
