answersLogoWhite

0

not usually. Suggest getting a plastic tank repair kit, (epoxy base) or for larger repairs, they make a tool like a solder iron that heats up a plastic block of material that you drip onto the crack and the old tank to seal it. Harbor freight sells them...

User Avatar

Wiki User

16y ago

What else can I help you with?

Related Questions

How do you clear the instrument panel light for coolant reservoir?

Check the coolant reservior for any leak. 1. If there is leak, try to stop the leak by A). go for coolant reservior replacement from dealership or from junk yard used part dealer. B). Stop the leak by putting adequate glue (i.e. glue which could sustain high temp) over the leak area. 2. If there is NO leak, it is probably a bad sensor, a known problem according to the Mazda Parts Dept. Replace the reservoir which includes the coolant sensor. They are sold as one part.


How can I effectively glue a hairline crack in wood?

To effectively glue a hairline crack in wood, follow these steps: Clean the crack with a damp cloth to remove any debris. Apply wood glue into the crack using a small brush or toothpick. Press the crack together and wipe away any excess glue. Clamp the wood together and let it dry according to the glue's instructions. Sand the area smooth once the glue has fully dried.


Can you use superglue on stained glass projects?

I wouldn't, superglue or CA glue when cured becomes very brittle, its like hard plastic, when your stained glass project flexes, (and it will) the the CA glue will crack and fail.


How do you fix a crack in acyrlic pool stairs?

you can get acrylic plastic glues however it may be a good idea to reinforce the glue over the crack from underneath where you cant see it . Or get a piece of acrylic the size of the whole step and glue it under the step. just make sure the surfaces are well prepared.


What is the best glue for vinyl plastic?

The best glue for vinyl plastic is a cyanoacrylate adhesive, also known as super glue.


How can I effectively repair a crack in a guitar neck?

To effectively repair a crack in a guitar neck, you can use wood glue to carefully glue the crack back together. Make sure to clamp the crack closed while the glue dries, and then sand and refinish the area to restore the appearance of the neck.


How can you safely fix a crack in the side of the plastic base of a bird cage until you can get a new cage?

I would remove the bird from the cage during the repair if possible, then place Krazy Glue or another good adhesive glue in the crack, the put duct tape over the top of the crack to help seal it in place. The fumes from the adhesive may irritate the bird, which is why you may want to relocate the bird until the glue sets (about 10 minutes or so).


What is the best glue for vinyl to plastic?

The best glue for bonding vinyl to plastic is a cyanoacrylate adhesive, also known as super glue.


Who invented Thermo Plastic glue?

Paul E. Cope invented Thermo plastic glue also known as "Hot Glue" it is used in Hot Glue guns.


Can a cracked intake on a ford 4.6 engine be fixed with epoxy glue or anything else the crack is about 3 long and made out of plastic?

If you're talking about that plastic box that holds the air filter - use duct tape.


What glue should I use for a soft plastic it is a flexible material?

A good glue you can use for soft plastic which is a flexible material is Gorilla Glue.


What might the problem be if you are spilling antifreeze from the passenger side underneath the coolant reservoir on a 1994 Saturn sc1?

You May Have A Hole Or Crack In The Bottom Of The Tank, It Can Be Repaired If This Is The Problem. Remove The Tank, Wash It Out. Fill It With Water If You Find A Leak. Buy Some 2 Part Epoxy Glue. Mix As Directed. Cover Hole Or Crack, Let Cure Couple Hours. Install This Should Take Care Of It. This Is Most Likely What Is Wrong. Good Luck