0
What else can I help you with?
Where is throttle position sensor on Kia Sedona?
The throttle position sensor (TPS) on a Kia Sedona is typically located on the throttle body, which is situated between the air intake manifold and the engine. To access it, you may need to remove any engine covers or components obstructing the throttle body. The sensor is usually mounted directly on the throttle body and has an electrical connector attached to it. Always refer to the vehicle’s service manual for specific details and instructions related to your model year.
How do you replace a throttle position sensor on a 2004 Kia Sedona?
I have no idea but ours in bad in our 2003 Kia Sedona 6 cyl and the dealership is charging us just over $900 to replace it. Sacramento, Ca. hi. i just replaced my throttle position sensor by myself. you can email me if you would like more information. its really not hard at all. my email is cleverchicks3@yahoo.com
Does anyone have any idea what the problem might be with my 2005 kia sedona minivan it goes off if I let the accelerator go?
More than likely throttle position sensor
What is the cost to replace a throttle position sensor for 2004 Kia Sedona?
The cost to replace a throttle position sensor for a 2004 Kia Sedona typically ranges between $100 and $300, including parts and labor. The sensor itself usually costs between $30 and $100, while labor charges can add another $70 to $200 depending on your location and the shop's rates. It's advisable to get quotes from multiple mechanics to ensure you're getting a fair price.
Location of camshaft position sensor on Kia Sedona?
A camshaft position sensor detects which cylinder is firing and establishes the coil firing sequence. In a Kia Sedona, it is located at the end of the intake camshaft.
How do you replace tps sensor 2005 Kia Sorento?
From the Kia Technical Service Bulletin: Download provides information related to the Throttle Position Sensor (TPS) for Sorento & Sedona models. Some Sorento & Sedona vehicles may exhibit diagnostic trouble codes P0121 and/or P1121. This condition mainly occurs in high ambient or desert areas, and can be related to the occasional increase in contact resistance due to excessive wear of the inner elements of the TP sensor. This bulletin describes the proper service and adjustment procedure for replacing the TP Sensor. - Effective Vehicle Information 2003-2006 Sorento 3.5L 2002-2005 Sedona 3.5L - Parts Information Part Name Previous Part No. New Part No. Throttle Position Sensor 35102 39000 35102 39000FFF - Service Procedure Replacement Procedure: 1. Turn ignition OFF. Remove engine cover and disconnect electrical connector from TP Sensor. 2. Remove two (2) retaining screws from TP Sensor and remove from throttle body. 3. Install new TP Sensor to throttle body. Install retaining screws and hand tighten lightly. Adjustment will be required. Re-install electrical connector to TP Sensor. 4. Install Global Diagnostic System. a. Select "System Option" b. Select "Idle RPM Adjust Mode" c. Apply Parking Brake 5. Select Neutral position and place engine in idle condition with A/C OFF. 6. Remove rubber plug and adjust using instructions provided on screen. Adjust TPS: 7. Using the GDS scan tool, monitor current data using two (2) parameters: • Closed Throttle Position Switch • Throttle Position Voltage Value 8. Open throttle by hand very slowly until idle switch status switches to OFF. Note the TPS voltage value. Voltage: 9. Close throttle and record the TPS voltage. Voltage: Closed throttle voltage should be 30~65mV less than the voltage noted in step eight (8). Adjust TP Sensor and repeat test as required.
How do you program the key doorlock buttons on a KIA Sedona after replacing the vehicle's battery?
Mind died on me and I replced the battery. Had to clean the inside and it worked fine.
Where can i find the Kia throttle position sensor?
well it depends on the model of Kia, sideways or rear wheel drive, but generally TPS sensor is mounted on the throttle dody , some on the top , most on the side. On my 02 Sedona. It is mounted on the back side of the throtle body. Mine went bad and I had to replace the complete throtle body unit. They do not sell only the sensor and it is a dealer only part but it is easy to install yourself if you are mechanicaly inclinded.
How do you remove the upper intake in a 2002 Kia Sedona?
To remove the upper intake on a 2002 Kia Sedona, first ensure the engine is cool and disconnect the negative battery cable. Then, remove any engine covers and disconnect the throttle body, vacuum lines, and electrical connectors attached to the intake. Next, unbolt the intake manifold using the appropriate socket, carefully lifting it off the engine while checking for any remaining connections or hoses. Finally, clean the mating surfaces before reinstalling or replacing the intake.
What causes a kia van sedona to skip?
It could be a number of things, but I would start at the fuel filter and work toward the throttle body. A lack of gas is pobably the problem.
Where is the idle air control of Kia Sedona 2005 located?
The idle air control (IAC) valve on a 2005 Kia Sedona is typically located on the throttle body. It is usually mounted on the side or top of the throttle body assembly, which is found near the intake manifold. To access it, you may need to remove any air intake components or hoses that obstruct visibility. Always consult the vehicle's service manual for specific instructions and diagrams.
Where is the coolant fan sensor fuse on a Kia Sedona?
The coolant fan sensor fuse on a Kia Sedona is typically located in the fuse box under the dashboard or in the engine compartment. In most models, the fuse box under the hood is usually found near the battery. To locate the specific fuse, refer to the owner's manual for the exact position and identification of the coolant fan sensor fuse. Always ensure the vehicle is turned off before checking or replacing any fuses.
