0
What else can I help you with?
How many watts is a titan hifonics txi4406 4x110?
The Hifonics TXi4406 amplifier is rated at 4 x 110 watts RMS at 4 ohms. This means each channel can output up to 110 watts of power into a 4-ohm load.
Does a 400 watt 2 channel amp have 2 channels of 400 watts each or 2 channels of 200 watts each?
500 and 27 watts
What is 50 watt hi fi amplifier?
This would be an audio amplifier which can produce 50 watts of power in each of its channels (hi fi, or high fidelity, was typically one or two). Measuring 50 watts, though, is tricky, as the way audio watts have been counted has changed over the years.
What is a bridgeable amplifier?
A bridgeable amplifier is a two channel amp where the two sections can be combined and used as a single channel amp with much higher (usually around double) power output. There will be a switch or jumper that enables the bridge. Only one of the two inputs are used. The output is taken from the two positive terminals, one from each channel. The negative or common output terminals are not used. A bridged amp fed from an electronic crossover is used a lot to feed a high-powered sub.
How many watts the pioneer have?
The term "Pioneer" could refer to various products, such as car audio systems, home theater receivers, or other electronics. Each product has different wattage ratings depending on its specifications. For example, a Pioneer car amplifier might range from 50 to several hundred watts per channel, while home audio receivers can vary widely, often between 50 to 150 watts per channel. To provide a precise answer, the specific Pioneer model in question would need to be identified.
How do you bridge three subs to a two channel amp?
3 passive sub at 8 ohm imp in parralel will be 2.6+ impedence.Most of the professional sum amp can take up to 2 ohms load per channel(check the spec of the Amp)eg: you should be able to connect max 4 subs in each channel(match the watts pwr to amp)
What speaker match a 1600 watt rms 2 channel amplifier?
To match a 1600 watt RMS 2-channel amplifier, you should look for speakers that can handle a power rating of at least 800 watts RMS per channel, assuming a standard setup where each channel drives one speaker. It's also important to consider the speaker's impedance; typically, 4-ohm speakers are a good match for higher power amplifiers, as they can draw more power. Additionally, ensure the speaker's sensitivity rating is suitable for your listening environment to achieve optimal performance.
How is the amplifier watt rated for example if its 350 watt and 2 channels does it produce a 350 watt at each channel or is it divided on the 2 channels so that it would be 175 watt for each channel?
if it is 350 rms by 2 channels it is 175 rms each channel unless it can be bridged than its 350 rms by 1 channel
Can you run two eight inch subwoofers requiring 50-100 watts of power each running at 4 ohms with a 2 channel 4 ohm amp putting out 75 watts per channel without damaging the subwoofers or the amp?
Yes
How many watt amplifier will power two 15 inch speakers?
It depends on the power handling capability of the speakers. Generally, a 500-600 watt amplifier would be sufficient to power two 15-inch speakers that have a power handling capacity of around 250-300 watts each. Make sure to match the amplifier's power output with the speakers' power handling to avoid damaging the speakers.
Is a 4 channel amplifier better than a mono?
It all depends on what your using it for, in example. If you have a 400 watt 4 channel amplifier then that means you can hook up 4 units to the amplifier at a 100 watts each (4x100=400). these units could be things such as door speakers, tweeters, mid ranges, anything that produces sound. A mono is no better than 4 channel it is just used for a different purpose. Mono or Mono-block amplifiers are used for subwoofers because they only have one slot to exert power from so the whole power of the amp is distributed to one source. The cool thing about 4 channel amplifiers is that you can get some decent aftermarket door speakers and hook them up to your 4 channel, turn on your high pass frequency filter, and blast those speakers as loud as you want without having your bass drown them out.
Your amplifier is 150Watts your speakers is 30Watts each for 4 pieces it will work?
You may have 1500 watts output but the speakers will only dissipate 30watts each the answer yes they will work fine as long as you do not increase the level whereby the speakers will have to dissipate 1500 watts because they will blow open with the extra output demand.
