The method of changing the deck belt will vary wildly with the many available decks, but there are a few common steps.
1: Remove the deck. (not necessary but recommended)
2: Notice the way that the belt is wound around the spindles. Take a picture if necessary.
3: Remove the belt. There will usually be a tensioning pulley that is pulling the belt tight with a spring. Remove the spring and release the pressure to pull the belt off.
4: Buy a new belt. Either find numbers on the belt, measure it, or bring it to a hardware store that can help you find the right size for your deck.
5: Install the new belt. Recall how it wound around each spindle and pulley, and install it. Replace any tensioning springs you might have removed.
6: Reattach the deck and try it out! There shouldn't be any vibrations or unusual noise.
Note: These steps are very general and vary by the individual deck.
How do you change a mower deck belt on a John Deere L130?Read more: How_do_you_change_a_mower_deck_belt_on_a_John_Deere_L130
make a drawing of how the old one is on it before replacing it,
Disingage the mower deck take off the mower deck look under neath their and replace the belt
To change the mower deck belt on an Exmark Lazer Z HP, first, ensure the engine is off and the key is removed. Raise the mower deck to its highest position and remove the deck from the mower by unhooking the suspension arms and disconnecting the drive belt. Once the deck is off, peel off the old belt from the pulleys and replace it with the new one, ensuring it follows the correct routing. Finally, reattach the deck and test the mower to ensure proper operation.
Impossible to answer without knowing year, make & model, of mower.
You can change a John Deere LA 175 mower deck belt configuration by checking the diagrams and instructions in the owner's or manufacturer's manual basically.
To change the drive belt on a John Deere GT235, first, ensure the engine is off and the key is removed. Raise the mower deck and remove the deck from the tractor for easier access. Then, remove the old drive belt by loosening the idler pulley and sliding the belt off the pulleys. Install the new belt by routing it according to the belt diagram, ensuring it sits properly on all pulleys, and then reassemble the mower deck.
To change the belt on a Sears GT5000, first, ensure the tractor is turned off and the key is removed. Remove the mower deck by detaching the pins and lift the deck out. Then, locate the drive belt, release the tension by moving the tensioner pulley, and carefully remove the old belt. Install the new belt by following the same routing as the old one, reattach the mower deck, and restore tension to the belt before testing the operation.
With proper replacement belt in hand, lower deck. ÊRemove grass catcher. ÊLocate the the locking mechanism, unlock and lower deck to the floor. ÊRemove the belt, wearing leather gloves, slide the belt around the engine pulley, a small screwdriver may be helpful.Reattach the grass catcher.
To change the belt on a Ford LT 12 mower deck, first, ensure the mower is turned off and disconnect the battery for safety. Remove the mower deck from the tractor by detaching any pins or brackets. Locate the old belt, note its routing path, and then remove it from the pulleys. Install the new belt by following the same routing, ensuring it sits properly in the pulleys, and reattach the mower deck to the tractor.
what model and which belt? If it is a 1000 series you have a transmission drive belt and a deck belt. I you have a 2000 series or higher or a cub cadet with an IH logo then you only have one belt the deck belt and no drive belt you have a drive shaft. So the model of the tractor and what belt needs to be given before the correct answer can be given.Phil
To change the drive belt on a John Deere 345, first, ensure the engine is off and disconnect the spark plug for safety. Remove the mower deck by detaching it from the tractor, then locate the drive belt. Remove the old belt by releasing the tension from the belt tensioner, and install the new belt by routing it according to the diagram typically found on the mower deck or in the owner's manual. Finally, reattach the mower deck and reconnect the spark plug before testing the setup.