Open the tail gate, lift the floor carpet at the rear. In some vehicles there are two layers of carpet.
There should be a 6 inch wide black metal panel running the width of the vehicle held down with a clip in the middle. Lift the handle, and turn 1/2 turn counter clockwise.
Lift the plate out towards you, using the clip as a handle.
In the middle of the space exposed is a silver 17mm nut. Use the wheel-brace (the spanner used to remove the wheel bolts) to undo this nut counter-clockwise.
From time to time check under the vehicle to see if the spare wheel cage has been released/lowered enough to unhook the cage and remove the wheel from the cage
Note, there may be a short "safety" rope which will need to be removed.
It is quite likely that on older vehicles the "hook" mechanism that is lowered using the above nut may have seized up due to corrosion, meaning the a new hook will have to be bought, and a hack-saw will be needed to cut the old hook off.
its to the right of the steering wheel
Two rubber clip either side of wheel then twist cover and pull
Wishbone needs replacing - rubbers have split or gone mishapen.
To remove the front bumper from a Vauxhall Zafira, first, ensure the vehicle is parked on a flat surface and disconnect the battery. Then, remove any screws or clips securing the bumper, typically located in the wheel arches, under the front, and along the top near the grille. Gently pull the bumper away from the body, taking care to disconnect any wiring for fog lights or sensors. Finally, lift the bumper off completely and set it aside.
zafira alarm is fitted inside drivers side wheel arch. whip off front wheel d/s remove inner wheel arch cover, hay presto..theres the little s**t..
To remove the spare wheel on a Citroen Xsara Picasso, first, locate the spare wheel compartment, usually found under the boot floor. Use the appropriate tool, typically a wheel brace or a spanner, to loosen the bolt securing the spare wheel in place. Once the bolt is removed, lift the spare wheel out of the compartment. Make sure to securely stow any tools or components after the wheel is removed.
To remove the spare wheel from a Peugeot 307, first, locate the spare wheel compartment, usually found in the trunk under the floor panel. Lift the panel and use the provided tools to loosen the securing bolt or clamp that holds the spare wheel in place. Once it's loose, carefully lift the spare wheel out of the compartment. Finally, ensure everything is securely placed back in the trunk before closing it.
To remove the spare wheel from a Nissan Civilian bus, first, locate the spare wheel compartment, typically found underneath the rear of the vehicle. Use the appropriate tools, such as a wrench or a jack, to lower the spare wheel from its mount. Ensure you follow safety precautions by securing the vehicle and using gloves if necessary. Once lowered, you can detach the wheel from the mounting mechanism.
I have a Chevy Blazer 2000 4 Wheel Drive ZR2 The Spare Is On The Back With a Lock How do I remove the Spare Tire Thank You
The tool kit and the jack for the Porsche Boxster are located in the front luggage compartment behind the spare wheel. You must remove the spare wheel to get to it.
To remove the spare wheel from a Citroën C2, first, locate the spare wheel compartment, typically found in the boot (trunk) under the floor mat. Use the provided tool to unscrew the retaining bolt or clamp that holds the spare wheel in place. Once the bolt is removed, lift the spare wheel out of the compartment. Ensure you securely store the tools back in their designated place after use.
Hi If Zafira 99-05 then lots of Torx/crossheads then pull off - Westfalia tow bars have good picture If 95 onwards then more complicated - looking at info I reckon : Remove rear light clusters - 2 knobs inside - if you've no spare wheel then you'll have to remove the emergency blow upkit to get at them. This will show you how bumper clips into locating lugs. Next undo 2 torqx in each wheel arch. Then remove 2 locating 'push in clips' on bottom of bumper - these may easily break so get spares beforehand. Then gently pull upwards and backwards - 2 person task to ensure that the upper location clips by light clusters dont break. Cant be sure of any other bolts so be careful Hope this helps