answersLogoWhite

0

The information below is listed in the 2008 HHR manual beginning on page 5-65. You can access the manual below.

Each TPMS sensor has a unique identification code. Any time you replace one or more of the TPMS sensors or rotate the vehicle's tires, the identification codes need to be matched to the new tire/wheel location.

The sensors are matched, to the tire/wheel locations, in the following order: driver side front tire, passenger side front tire, passenger side rear tire, and driver side rear tire using a TPMS diagnostic tool.

See your dealer/retailer for service.

The TPMS sensors can also be matched to each tire/wheel position by increasing or decreasing the tire's air pressure. When increasing the tire's pressure, do not exceed the maximum inflation pressure indicated on

the tire's sidewall. To decrease the tire's air-pressure use the pointed end of the valve cap, a pencil-style air pressure gage, or a key.

You have two minutes to match each tire and wheel position. If it takes longer than two minutes to match any tire and wheel position, the matching process stops and you need to start over.

The TPMS matching process is outlined below:

1. Set the parking brake.

2. Turn the ignition switch to ON/RUN with the engine off.

3. Press and hold the Remote Keyless Entry (RKE) transmitter's LOCK and UNLOCK buttons, at the same time, for about five seconds to start the TPMS learn mode. The horn sounds twice indicating the TPMS receiver is ready and in learn mode.

4. Start with the driver side front tire. The driver side front turn signal also comes on to indicate that corner's sensor is ready to be learned.

5. Remove the valve cap from the tire's valve stem.

Activate the TPMS sensor by increasing or decreasing the tire's air pressure for about eight seconds. The horn chirp, can take up to 30 seconds to sound. It chirps one time and then all the turn signals flash one time to confirm the sensor identification code has been matched to the

tire/wheel position.

6. The passenger side front turn signal comes on to indicate that corner sensor is ready to be learned. Proceed to the passenger side front tire and

repeat the procedure in Step 5.

7. The passenger side rear turn signal comes on to indicate that corner sensor is ready to be learned. Proceed to the passenger side rear tire and

repeat the procedure in Step 5.

8. The driver side rear turn signal comes on to indicate that corner sensor is ready to be learned. Proceed to the driver side rear tire, and repeat

the procedure in Step 5.

9. After hearing the single horn chirp for the driver side rear tire, two additional horn chirps sound to indicate the tire learning process is done. Turn the ignition switch to LOCK/OFF. If no tires are learned after entering the TPMS learn mode, or if communication with the receiver

stops, or if the time limit has expired, turn the ignition switch to LOCK/OFF and start over beginning with Step 2.

10. Set all four tires to the recommended air pressure level as indicated on the Tire and Loading Information label.

11. Put the valve caps back on the valve stems.

User Avatar

Wiki User

13y ago

What else can I help you with?

Related Questions

Will aftermarket wheels on a Chevy hhr 08 fit a Toyota Camry 08 both are 5 lug front wheel drive?

No they will not.


Which fuse controls tail lites on a 08 hhr?

Under the hood. Fuse number 69 is the tail light fuse


When was Virgile Reset born?

Virgile Reset was born on 1985-08-03.


How much is an 08 Chevy duramax?

the average price for a 08 Chevy duramax is around 100 to 200 dollhairs. Hoped i Helped Love, Kyle Scribner


What does Jason Aldean drive?

08 Chevy silverado


How do you reset the service message on a Renault Espace after oil change?

see:- http://grumunkin.blogspot.com/2009/08/how-to-reset-service-indicator-on.html :-)


How do you reset low tire pressure light on Chevy Trailblazer?

The TPMS sensor matching process for 08 TrailBlazer LT is outlined below: Set the parking brake. Turn the ignition switch to ON/RUN with the engine off. Turn the headlamp control from off to parking lamps four times within three seconds. A double horn chirp will sound and the TPMS low tire warning light will begin to flash. The double horn chirp and flashing TPMS warning light indicate that the TPMS matching process has started. The TPMS warning light should continue flashing throughout the matching procedure. Start with the driver side front tire. Remove the valve cap from the valve cap stem. Activate the TPMS sensor by increasing or decreasing the tire's air pressure for 10 seconds, then stop and listen for a single horn chirp. The single horn chirp should sound within 15 seconds, confirming that the sensor identification code has been matched to this tire and wheel position. If you do not hear the confirming single horn chirp, you will need to start over with step number one. Proceed to the passenger side front tire, and repeat the procedure in Step 5. Proceed to the passenger side rear tire, and repeat the procedure in Step 5. Proceed to the driver side rear tire, and repeat the procedure in Step 5. After hearing the confirming horn chirp for the driver's side rear tire, check to see if the TPMS warning light is still flashing. If yes, turn the ignition switch to LOCK/OFF to exit the sensor matching process. If the TPMS warning light is not flashing, the five minute time limit has passed and you will need to start the process over beginning with Step 1. Set all four tires to the recommended air pressure level


What kind of car does Jason Aldean drive?

Jason Aldean drives a '08 Chevy Silvarado. He is sponsored by Chevy.


How do you reset the service now after oil change on 08 touareg?

It's in the driver information screen between the speedometer and odometer. There should be an option to reset it.


Reset the maintenance required light on 08 Toyota rav 4?

maintenance with engine


Will a fender from a 07 Chevy Cobalt fit on a 08 cobalt?

Yes it will.


How many cilinders are in the 08 Chevy colorado3.7l?

It is an inline 5 cylinder.