answersLogoWhite

0

Take the spark plug out of the #1 cylinder. Have someone stick a finger over the hole (but not into it, naturally). Bump the starter until a burst of air pushes their finger out. That's the point where the #1 cylinder is at Top Dead Center. Replace the spark plug and spark plug wire. Unbolt the distributor to loosen it. Hook up the timing light.. the red cable to the battery positive, the ground to either the battery negative or a good ground point, and the last cable goes on the wire to the #1 spark plug. Start the vehicle, and aim the timing light at the timing marks. Rotate the distributor to advance or retard the ignition timing until it's right.

User Avatar

Wiki User

12y ago

What else can I help you with?

Related Questions

How do you set timing on 1995 Cadillac deville?

How do you set timing on a 1995 Cadillac Deville


How do you set the timing on a 1998 Cadillac Deville?

how do i set the timing on a 1998 cadillac deville 4.6


What are the procedures for timing a 1993 Cadillac brougham with a 5.7liter TBI?

To time a 1993 Cadillac Brougham with a 5.7-liter TBI engine, first, ensure the engine is at operating temperature. Disconnect the timing connector (usually a tan wire with a black stripe) to set the timing control to the base timing mode. Use a timing light to check the timing marks on the harmonic balancer, adjusting the distributor as necessary to achieve the specified timing of 0 degrees BTDC. After adjustment, reconnect the timing connector and recheck the timing to ensure it remains correct.


How do you set timing on 1992 Cadillac 4.9?

how do i set my timeing on a 1992 cadillac v8 4.9 liter


How do you set clock on a 1989 Cadillac Brougham?

To set the clock on a 1989 Cadillac Brougham, first turn the ignition to the "On" position. Locate the clock setting button, usually found on the dashboard or near the radio. Press and hold the "H" button to set the hour, and use the "M" button to adjust the minutes. Release the buttons once the desired time is displayed.


How do you set the clock on 1988 Cadillac Brougham this is not the smaller sized Cadillac Fleetwood and there is no set button on the AM FM Cassette player?

Turn the ignition to run. On the radio controls, PULL the scan button out to set the hour. Once the the hour is correct, PULL the seek button out to set the minutes.


What is Correct ignition timing for a 1992 Cadillac brougham?

The correct ignition timing for a 1992 Cadillac Brougham equipped with the 5.7L (350 cubic inch) engine is typically set at 10 degrees before top dead center (BTDC) at idle, with the engine warm and the transmission in gear. However, it's always recommended to verify this with the vehicle's service manual or a label under the hood, as variations can occur based on specific engine configurations or emissions systems. Adjustments may also depend on factors like altitude and fuel type.


How do i set the timing on a 1990 Cadillac Seville 4.5 liter?

To set the timing on a 1990 Cadillac Seville 4.5 liter, first ensure the engine is at operating temperature and turned off. Locate the timing marks on the harmonic balancer and the timing cover. Use a timing light to check the current timing, then loosen the distributor hold-down bolt and adjust the distributor to align the marks to the specified timing setting, typically around 10 degrees BTDC. Finally, retighten the distributor bolt and recheck the timing to ensure accuracy.


How can you set the ignition timing on a 1991 Cadillac Brougham?

unplug the wire on the right side of the firewall it should be close to your heater core hoses it is a small wire a male@female connector unplug it . now unloosen your distributor set your timing to 0 Titan up your distributor now plug up the wire.remember the car must be running to do this.now once you have done. unplug the negative side of your battery for 30sec to remove any bad codes.p.s remember to start car before you start this job.


How do you set timing on 1963 Cadillac?

disconnect vacumn advance hose, bring down to curb idle, connect timing light to the # 1 spark plug wire, loosen distibutor and adjust as necessary


What timing do I set a 1963 Cadillac 390 engine?

To set the timing on a 1963 Cadillac 390 engine, you should aim for an initial timing of around 8 to 12 degrees before top dead center (BTDC). Use a timing light to check this while the engine is idling. Ensure the vacuum advance is disconnected during this process and reconnected afterward. Always refer to the specific service manual for your vehicle, as slight variations may exist based on different configurations or modifications.


How do you set the timing on a 998cc leyland mini?

what timing are you trying to set? the cam timing or the ignition timing?