0
The cost to replace a PK3 key can vary depending on the locksmith or dealership, but typically ranges from $50 to $150. Factors such as programming, the specific vehicle model, and location may influence the price. It's advisable to get quotes from multiple sources to find the best deal.
What else can I help you with?
What type of car key pk3?
Most General Motors built cars are now using the PK3 Transponder key.
How do you program a new pk3 key without the original?
Hi, from all I've read about it on the net, (and in my 2003 Olds Silhouette owner's manual) you cannot program the PK3 key yourself UNLESS you have at least one already programmed PK3 (master) key. You must go to your dealer if you don't have at least one programmed (original) PK3 key,..they have the special equipment to do it.
Does a 2000 Chevy Venture van have a resister or computer chip key?
Yes the key is chipped. You need a pk3 key. You can get them from eBay for around $15 uncut.
How you program a key for a Chevy venturer 2000?
If you want to program a new PK3 Key, there is a procedure at the bottom of the linked page.Take Care,Greg
What does pk3 mean in your 2000 Buick park avenue key?
In the context of your 2000 Buick Park Avenue key, "PK3" refers to a type of anti-theft system known as the Passkey III. This system uses a transponder chip embedded in the key, which communicates with the vehicle's ignition to ensure that only the correct key can start the engine. If a non-compatible key is used, the vehicle's security system will prevent it from starting, enhancing overall security against theft.
How do you reset 1999 Chevy Venture passlock?
the 1999 venture has the PK3 system for security, so you have to go to a GM dealer or a automotive locksmith that has the proper box to reset it or make a new master key for it.
Can you program a transponder key without the origanal key?
General Motors PK3*, PK3+*, and Circle Plus* keys can be programmed without an original key present (but the new key has to be cut correctly to turn your ignition!)The Procedure for this is:1. Insert a new cut key in ignition and turn key to the ON position for10 minutes (or until the security light goes out).2. Within 45 seconds turn the key to OFF and then back to the ON position for10 minutes (or until the security light goes out).3. Within 45 seconds turn the key to OFF and then back to the ON position for10 minutes (or until the security light goes out).4. Turn key OFF then back ON. The key is now programmed.Start vehicle to test key.** Note: To tell if your General Motors keys are the ones listed above, it will be stamped on the blade of the key just below the plastic head. (The 'circle plus' is actually a circle with a '+' sign in the middle of it)
2000 Pontiac Grand Prix turn the key all dashboard lights come on but car will not turn over or make any sound Car has a new battery and plenty of gas Could it be the key?
It could be the key if the security or anti-theft light is flashing. If it is flashing than either the key is not sending a signal or the lock cylinder PK3 receiver is not receiving a signal.
How long is a servo belt to an 1996 Nissan 300zx na?
The belt is a PK3 & its 925mm long.
How do you apply mods to Jedi knight Jedi outcast?
Mods are usually contained within a .pk3 file. This file should not be expanded, but placed into your base Jedi Knight II/Gamedata/Base folder. If the file is not a .pk3 file, but a folder containing other files, then this folder should be placed in your Jedi Knight II/Gamedata folder, but the Base folder.
How can I install Windows XP Home edition with service pk3 where Windows XP with service pk 2 was previously installed?
XP Home Sevice PK
Where is the pass key light on a 1997 Grand prix?
look at your keys, does it say PK3 or anything of the liking on it? if so you have a passkey system. Otherwise if you are just looking for a security light, check above the reset odometer button. its dull but you can see the cut out. mine does not turn on at anytime with the car running or not. Your results may vary.
