answersLogoWhite

0

To check a draw on a circuit you need to decide a few things and think about you situation.

  • What am I trying to do. I have an unexplained draw? I want to know how much this circuit is drawing while operating? Is it blowing fuses or cycling the breaker?
  • What tools do I have available?
  • Do I have a wiring diagram?

If we have a draw on the system killing the battery and we have a test light. We can disconnect the battery and place the test light between the battery terminal and the cable. A draw of consequence should light the bulb dimly. Then we start removing fuses and checking the light until the offending circuit is found.

If we have a ammeter we can determine what amperage is being drawn, what circuit is drawing and so on using basically the same techniques.

To figure out what is wrong a wiring diagram is invaluable as it will be a map to tracing the circuit through the car.

User Avatar

Wiki User

13y ago

What else can I help you with?

Related Questions

How to check the amperage of an electrical circuit?

To check the amperage of an electrical circuit, you can use a clamp meter. Simply clamp the meter around one of the wires in the circuit to measure the current flowing through it. Make sure to set the meter to the appropriate amperage range before taking the reading.


What is a short to voltage?

what is short to voltage in a car electrical circuit & how to check it ?


What type of material will you find outside of an electrical circuit to protect it?

You will typically find materials like insulation, enclosures, and grounding systems outside of an electrical circuit to protect it from environmental factors, physical damage, and electrical hazards. These materials help to ensure the safety and functionality of the electrical system.


What is electrical shock sensation?

It is the hard way finding out that the electrical circuit is still energized. It is much easier on the body if a tester is used to check for voltage before any work is started on any electrical circuit.


Is the breaker switch loose in your electrical system?

It is important to check if the breaker switch in your electrical system is loose.


What is the problem if engine stays running after car turned off in 1988 Chevy caprice 305?

Check your electrical system. You probably have a short circuit, melted switch, or ghost(and no I do not mean a creepy spooky ghost) in the system.


Possible electrical problem will my microwave oven be okay?

Check the circuit breaker to see if it tripped.


Your home ac is not cooling?

First check to make sure that the system has freon, if not then you will have a leak then check the electrical system................


What is the maximum check amount that can be processed through this system?

The maximum check amount that can be processed through this system is 10,000.


How can I fix an open ground issue in my electrical system?

To fix an open ground issue in your electrical system, you should first turn off the power to the affected circuit. Then, check the wiring connections to ensure they are secure and properly connected. If you find any loose or damaged wires, repair or replace them as needed. Finally, test the circuit with a multimeter to confirm that the ground connection is now functioning correctly. If you are unsure or uncomfortable working with electrical systems, it is best to consult a licensed electrician for assistance.


How can I troubleshoot a dead end 3-way switch in my home's electrical system?

To troubleshoot a dead end 3-way switch in your home's electrical system, start by checking the circuit breaker to ensure it is not tripped. Next, use a voltage tester to check if there is power reaching the switch. If there is power, the issue may be with the switch itself and it may need to be replaced. If there is no power, check the connections at the switch and the other switch in the circuit to ensure they are secure. If the issue persists, it may be necessary to call a professional electrician for further assistance.


How can I fix a hot and ground reversed issue in my electrical system?

To fix a hot and ground reversed issue in your electrical system, you should first turn off the power to the affected circuit. Then, you need to swap the wires connected to the hot (black) and ground (green or bare) terminals at the outlet or switch. Make sure to double-check your work and test the circuit before turning the power back on to ensure it is corrected. If you are unsure or uncomfortable working with electrical systems, it is best to consult a licensed electrician for assistance.