answersLogoWhite

0

What else can I help you with?

Related Questions

Are the door and ignition keys the same on a 1963 Chevrolet impala?

Yes. If you have one with no keys, simply remove the passenger side door lock and take it to your local locksmith who can make a key from the 4 digit code stamped into it, for less than $25. That, or risk destroying the ignition switch trying to get it out of the dash with no key. Door lock easy, dash ignition switch with no key--very difficult.


How did they make the lock?

It all depends on what kind of lock. It could be a lock in a canal, a door lock, an ignition lock on a vehicle, a lock of hair, a padlock, or any of many kinds of locks.


Where is the key code for the ignition key?

The key code for an ignition key is different for each make and model of car. The thing to do is contact the dealership or a locksmith to find the correct key code for the make and model of the vehicle in question.


24 Hour Locksmith in Sugar Land Automotive Service?

Replacement Auto Chip Key, Automobile locksmith,Auto Key Duplication, Chip Key Programming,How To Unlock Car Doors, Opening Car Door , Transponder Key Programming , 24 Hour Auto Locksmith Service , Make a Key For a Car , Ignition Cylinder Lock Repair , Replacing Lost Car Keys , Auto Door Lock Replacement , Car Ignition Key Replacement , Car Remote Replacement , Ignition Lock Removal , Ignition Lock Cylinder , Open a Locked Car Door , Replacement Keys For Cars , Key Ignition Locked , Car Door Locks Key Ignition Replacement , 24 Hour Auto Locksmiths , Car Unlocking 


1996 grand Cherokeee Laredo the passenger front door lock does not lock when you use the remote door lock any clues on what to check to find the problem?

It is probably a bad power lock actuator. it is inside the door, before removing it make sure that when the button is pressed there is power to the wire connector, if not check for cracked or broken wires leading into the door.


318 starts then dies?

Turn your ignition key backwards to put your auxiliary power on. Make sure all your windows are up, and then get out and hit the LOCK DOOR button a few times to lock all your doors. Now shut your driver-side door and go to your passenger door. Use your key to open the door, BUT when you turn to unlock it, turn it a few times. Now get in and try to start it. Let me know if that works 807-597-6178 Brian


How do you make the door locks automatically lock when you drive?

Get in car and shut the door turn key to position 2 you can see the marks near the ignition switch turn off radio so you can hear push the button to lock the doors hold till you hear a click noise, about 5-10 seconds after the doors lock turn ignition key to off position and remove key This setting should lock all doors at 9mph and unlock driver door when put into park.


What can you do if the doors on your car won't unlock with the keys?

OK, I'm assuming you can lock/unlock the doors with the door pins. If so, you will need to pull one of the door lock cylinders (preferably the passenger door because it gets used less) and take it too a locksmith and have him make a key to fit it.


How do you make your child lock button on the door stay unlocked?

Take te child lock off of the door


How can I replace a sliding glass door lock?

To replace a sliding glass door lock, you will need to remove the old lock by unscrewing it from the door. Then, you can install the new lock by following the manufacturer's instructions and securing it in place with screws. Make sure the new lock is compatible with your door before installing it.


Why does electric door lock on 2003 Grand Caravan start make a screeching or buzzing noise when you lock or unlock car?

The door lock actuator is going bad.


How can I replace the lock on a sliding glass door?

To replace the lock on a sliding glass door, you will need to remove the old lock by unscrewing it from the door. Then, you can install the new lock by following the manufacturer's instructions. Make sure the new lock fits properly and securely on the door before testing it to ensure it functions correctly.