answersLogoWhite

0

Pressing the accelerator before turning off the engine is generally not recommended, as it can lead to unnecessary wear on the engine and drivetrain. Doing so may also cause the vehicle to lurch or stall, which can be unsafe. It's best to let the engine idle for a moment before shutting it off to ensure a smooth and safe shutdown.

User Avatar

AnswerBot

1mo ago

What else can I help you with?

Related Questions

How do you change a accelerator cable on a 95 lumina van?

The accelerator cable is connected with a swivel nut on each end of the cable. Loosen the swivel nut, by turning it to the left. The accelerator cable will come off. Reverse the process to install the new accelerator cable.


Engine stalls or dies when stopping or turning?

The idle speed needs adjusted upward if an engine stalls when you take your foot off the accelerator while stopping or turning.


What is revving a car mean?

To rev the engine simply means pressing the accelerator down with the car in neutral as if you are preparing to take off fast for a race.


How do you reset a Mac?

You can reset the firmware by turning off the Mac, unplugging all cords from it, waiting 15 seconds, and turning it back on. You can reset the PRAM by turning it off, pressing the power button to turn it back on, quickly pressing and holding the Command+Option+R+P keys before the gray screen comes on, and holding those keys till you hear the startup sound for a second time. To reset the entire installation of OS X, you can insert the install disk that came with the Mac, turn it off, hold down the "C" key, turning it on, and then you will be presented with different options.


When enine is turning over there is a noise from the enginewhen you press accelerator pedal it goes off any ideas?

Spray belt dressing on your fan belts


How does the Xbox 360 turn on?

Either by pressing the power button, or by turning on a controller when your console is off. Hope This Helps! -MidKnight777


How do you take off on an incline without switching off?

To take off on an incline without switching off, ensure that your vehicle is in the correct gear for the slope. Gradually release the clutch while simultaneously pressing the accelerator to build up enough power to overcome gravity. Use the handbrake to hold the vehicle in place until you have sufficient throttle to prevent rolling backward. Smooth coordination of the clutch and accelerator is key to a successful launch on an incline.


How do you switch off spanner light on 2007 Renault clio?

To switch off the spanner light on a 2007 Renault Clio, you typically need to reset the service indicator after performing any required maintenance. This can be done by turning the ignition to the "ON" position without starting the engine, then pressing the accelerator pedal three times within 10 seconds. After this, the spanner light should turn off. If the light remains on, it may indicate an ongoing issue that needs to be addressed.


Do you have to drain toilet before turning it off?

It might be the best idea.


How do you turn off the change oil light on 2000 Oldsmobile?

I have a 2000 Olds Silohuette. I just reset the "Change Oil" light by turning the ignition to on(DO NOT START THE VEHICLE), pushing the accelerator down to the floor 6 times, turning the ignition off, and then starting the van. The light did not come on. Hopefully this will help.


Should you turn off a portable generator before turning off the appliances it powers?

Yes, it is recommended to turn off the portable generator before turning off the appliances it powers. This helps prevent potential damage to the appliances from power surges or fluctuations when the generator is turned off.


What are the basic steps for driving a manual car?

Driving a manual car involves several fundamental steps. Firstly, ensure the car is in neutral by pressing the clutch pedal and shifting the gear stick to the middle position. Start the engine and gradually press the clutch while shifting the gear stick into first gear. Slowly release the clutch while gently pressing the accelerator to start moving. To change gears, lift off the accelerator, press the clutch, shift to the desired gear, and then release the clutch while gradually applying the accelerator again. Rem