0
What else can I help you with?
What is the price range for a 2007 Mitsubishi Galant?
The average resale value you can expect to get for your 2007 Mitsubishi Galant is approximately $11,000 depending on body style, mileage, and condition.
What does error code P0442 on 2007 Mitsubishi Endeavor mean?
Error code P0442 on a 2007 Mitsubishi Endeavor indicates a small leak in the evaporative emissions control system (EVAP). This system is responsible for preventing fuel vapors from escaping into the atmosphere. The code can be triggered by issues such as a loose or damaged gas cap, a faulty EVAP canister, or leaks in the EVAP lines. It's advisable to inspect the gas cap first and then check for other potential leaks in the system.
What is the size of the oil drain plug on a 2007 Mitsubishi Galant 2.4l?
It takes a 15mm wrench.
Is the 2007 Mitsubishi Galant an interference engine?
Yes, the 2007 Mitsubishi Galant is equipped with an interference engine. This means that if the timing belt fails, the pistons can collide with the valves, potentially causing significant engine damage. Regular maintenance and timely replacement of the timing belt are crucial to prevent such issues.
Does the 2007 Mitsubishi Galant have a cabin air filter?
I thought it would but then after I bought one and tried to install it, I noticed it did not. I guess its not needed for some reason.
Can a 2007 Mitsubishi Galant motor fit in a 2003 Mitsubishi Galant frame?
Yes, with very little to no modification, from what I understand you can use the same trany from your 03 as well as the computer, and the motor should line up with mounts no problem. Make sure the motor you're trying to drop is a 6G75 3.8L and not a 4G69 2.4L.
Where is the orifice tube located on a Mitsubishi Galant 2007?
The orifice tube on a 2007 Mitsubishi Galant is located in the HVAC system, specifically within the refrigerant line that connects the condenser to the evaporator. It is typically found in the high-pressure side of the A/C system, often near the firewall or close to the evaporator unit in the engine compartment. Accessing it may require some disassembly of components to reach the tubing.
2007 Mitsubishi Galant orifice tube located?
The orifice tube in a 2007 Mitsubishi Galant is located in the air conditioning system, specifically within the liquid line that runs between the condenser and the evaporator. To access it, you'll typically need to remove the front bumper and possibly the condenser, as the orifice tube is often mounted near the condenser outlet. It's crucial to ensure the A/C system is properly evacuated before attempting to replace the orifice tube.
How do you remove the radio in a 2007 Mitsubishi Galant?
To remove the radio in a 2007 Mitsubishi Galant, start by disconnecting the negative battery terminal to ensure safety. Next, use a flathead screwdriver or a trim removal tool to carefully pry off the trim panel surrounding the radio. Once the trim is removed, unscrew the bolts holding the radio in place, disconnect the wiring harness and antenna cable, and then gently pull the radio out. After that, you can install the new radio by reversing the steps.
Where is the iat located on a 2007 Mitsubishi Galant?
The Intake Air Temperature (IAT) sensor on a 2007 Mitsubishi Galant is typically located in the intake manifold or attached to the air intake duct. It is usually situated near the air filter or throttle body, where it can accurately measure the temperature of the incoming air. To access it, you may need to remove some components in the engine bay for better visibility. Always refer to the vehicle's service manual for specific instructions and location details.
What type of automatic transmission fluid does a 2007 Mitsubishi galant use?
It should say it under the hood where you put the transmission fluid at.. If not call up a car parts place like autozone or something they will no
How do you change the driver side mirror on a 2007 Mitsubishi Galant?
To change the driver side mirror on a 2007 Mitsubishi Galant, first, carefully remove the interior door panel by unscrewing the necessary fasteners and gently prying it off. Disconnect the wiring harness for the mirror if it's powered. Next, remove the bolts or screws securing the mirror to the door, then take out the old mirror and replace it with the new one. Reattach the wiring harness, secure the new mirror with bolts or screws, and reassemble the door panel.
