answersLogoWhite

0

Remote Control Door Lock Receiver

User Avatar

Wiki User

13y ago

What else can I help you with?

Related Questions

How do you program a key fob for a 2004 Pontiac Grand AM?

== All transmitters that are to be recognized by the remote control door lock receiver (RCDLR) must be programmed in a single programming sequence. If the system is placed in program mode, all previously programmed transmitters will be erased upon receipt of the programming signal from the first transmitter. Up to 4 transmitters can be programmed. Do not operate or program the transmitters in the vicinity of other vehicles that are in the keyless entry program mode. This prevents the programming of the transmitters to the incorrect vehicle. The order in which the transmitters are programmed is important. The first transmitter programmed will be transmitter #1, and the second transmitter programmed will be transmitter #2. Use care to program the transmitters correctly. The scan tool must stay connected until all of the transmitters are programmed. # Install a scan tool. # Turn ON the ignition with the engine OFF. # With the scan tool, select Body, go to Remote Function Actuation. # Select Special Functions. # Select Program Key Fobs. # Select the number of key fobs to be programmed. # Press and hold the LOCK and the UNLOCK buttons simultaneously on the first transmitter for approximately 15 seconds. The power locks should cycle to confirm programming of the first fob is complete. # If you are programming more than one transmitter, repeat the previous step to program up to 4 transmitters. # Remove the scan tool. # Exit the vehicle. Attempt to lock/unlock the doors to verify the programming. # Operate the transmitter functions in order to verify correct system operation. == All transmitters that are to be recognized by the remote control door lock receiver (RCDLR) must be programmed in a single programming sequence. If the system is placed in program mode, all previously programmed transmitters will be erased upon receipt of the programming signal from the first transmitter. Up to 4 transmitters can be programmed. Do not operate or program the transmitters in the vicinity of other vehicles that are in the keyless entry program mode. This prevents the programming of the transmitters to the incorrect vehicle. The order in which the transmitters are programmed is important. The first transmitter programmed will be transmitter #1, and the second transmitter programmed will be transmitter #2. Use care to program the transmitters correctly. The scan tool must stay connected until all of the transmitters are programmed. # Install a scan tool. # Turn ON the ignition with the engine OFF. # With the scan tool, select Body, go to Remote Function Actuation. # Select Special Functions. # Select Program Key Fobs. # Select the number of key fobs to be programmed. # Press and hold the LOCK and the UNLOCK buttons simultaneously on the first transmitter for approximately 15 seconds. The power locks should cycle to confirm programming of the first fob is complete. # If you are programming more than one transmitter, repeat the previous step to program up to 4 transmitters. # Remove the scan tool. # Exit the vehicle. Attempt to lock/unlock the doors to verify the programming. # Operate the transmitter functions in order to verify correct system operation.


How do you reprogram a key less entry remote for Pontiac Montana?

... The following was taken from the Service Information for a 01 Montana. I can not verify it will work: Transmitter Programming Important All transmitters which are to be recognized by the remote control door lock transmitter (RCDLR) must be programmed in a single programming sequence. If the system is placed in program mode it will erase all previously programmed transmitters upon the receipt of the programming signal from the first transmitter. Up to four transmitters can be programmed. Do not operate or program the transmitters in the vicinity of other vehicles that are in the keyless entry program mode. This prevents the programming of the transmitters to the incorrect vehicle. 1. Remove the ignition key from the ignition lock cylinder. 2. Remove the BCM PRGRM fuse from the fuse block. 3. Close all of the doors. 4. Insert the ignition key into the ignition lock cylinder. 5. Turn the ignition to ACC. The body control module (BCM) will perform the following in order to identify the type of BCM installed in the vehicle: Flash the seat belt indicator 2, 3, or 4 times. Chime 2, 3, or 4 times. 6. Turn the ignition to OFF, and then back to ACC within 1 second. The BCM may begin to chime and flash diagnostic trouble codes (DTCs). If the BCM has stored any DTCs, refer to Diagnostic System Check - Body Control System in Body Control System. 7. Open and then close any vehicle door. The BCM will chime in order to confirm that the programming mode has been entered. 8. Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for approximately 14 seconds. Important After approximately 3-5 seconds the BCM will chime once to confirm that the programming has been completed for that transmitter. 9. Repeat the previous step in order to program each additional transmitter. 10. Remove the ignition key from the ignition lock cylinder. 11. Install the BCM PRGRM fuse into the fuse block. 12. Operate the functions of each transmitter in order to verify correct system operation.