0
What else can I help you with?
What does a P1128 error code on a 2006 Dodge Stratus mean?
Trouble code P1128 means: Closed Loop Fueling Not Achieved - Bank 1
What is Porsche boxster fault code p1128?
any ideas?
Dealer code P1128 on 2000 VW Beetle 2.0L what needs to be done?
Trouble code P1128 means: Long Term Fuel Trim Add. Air. Bank 1 System Too Lean
What are Porsche boxster diag codes p1130 p1128 p1126 and p1133?
what is p1133
Check engine light came on with a 2000 Boxster and the computer codes read P1128 and P1130?
Trouble code P1128 means: O2S Range 2 Cyl. 1-3 Trouble code P1130 means: O2S Range 2 Cyl. 4-6
What does 2002 Camry error code P1128 mean?
P1128 TOYOTA - Throttle Control Motor Lock MalfunctionPossible causes, Faulty Throttle Control Motor,Throttle Control Motor harness is open or shorted,Throttle Control Motor circuit poor electrical connection
What does P1128 code mean in a 2009 dodge grand caravan mean?
Bank one fuel system lean. Test fuel pressure, check for vacuum leaks,
How do you fix code p1128 for vw beetle?
i have the same code i search on the internet and i found that is the MAF sensor (mass air flow sensor) clean it or replace it it cost about 100
How do i fix the P1128 for 2009 jeep liberty?
The P1128 code on a 2009 Jeep Liberty typically indicates an issue with the fuel/air mixture, often related to the fuel trim or oxygen sensors. Begin by checking for vacuum leaks, which can affect air intake, and inspect the mass airflow sensor for dirt or damage. If these components are functioning properly, consider testing or replacing the upstream oxygen sensors. Finally, clear the code and take the vehicle for a drive to see if the code returns.
What do the check engine light codes P1128 and P1130 on a 2000 Porsche Boxster mean?
The OBDII engine codes generally have the same meaning regardless of which car you have. So, a code P1128 on a Porsche will have the same meaning (generally) on a VW Bug, for example.------------ Code P1128 ---------------- This code is usually present if your engine is running in a "Lean" air/fuel mixture situation. This code may be present as a secondary code to your P1130 code which indicates a bad air/fuel sensor (see below). My suggestion is to fix code P1130 first (bad air/fuel sensor) and then see if code P1128 goes away. If not, consider the following as possible causes of P1128....(1) any unmetered air introduced into the engine can cause P1128 to set. Tips: Carefully check for vacuum leaks. Include all areas that might introduce unmetered air to the engine. Don't forget exhaust leaks before the O2 sensors.(2) In some cases, this may also indicate a bad O2 sensor (Oxygen sensor). Cars usually have more than one O2 sensor and you should be getting an additional trouble code specifically indicating a bad 02 sensor. If not, then your O2 sensor is probably okay.(3) In some cases, a Mass Air Flow sensor may also cause this trouble code, but again, there should be an additional trouble code specifically indicating that you have a bad MAF sensorOther things to check...(A) Check and verify that fuel pressure is in specification. (B) If vacuum leak and fuel pressure checks are normal, check the air flow signal from the MAF sensor using a scan tool.--------- Code P1130 -----------Air fuel sensor (common problem!). You probably need a new air fuel sensor.
What does error code p1128 on a 2008 dodge ram mean?
Error code P1128 on a 2008 Dodge Ram indicates that the powertrain control module (PCM) has detected a problem with the fuel trim system, specifically related to the air-fuel mixture being too lean. This code often points to issues such as a vacuum leak, malfunctioning fuel injectors, or problems with the mass airflow sensor. It may also suggest that the engine is not receiving enough fuel. Diagnosing the exact cause typically involves checking the fuel system, intake leaks, and related sensors.
What is p1128-closed loop fueling not achieved - bank 1?
it means a oxygen sensor on bank 1 is not working. you need to find bank 1 and figure out if it is sensor 1 or 2. sensor 1 is in front of the cat. converter. sensor 2 is behind the converter
