answersLogoWhite

0

my speeco 20 ton model uses Wix 51553 filter.

User Avatar

Wiki User

16y ago

What else can I help you with?

Related Questions

How and where do you put the hydrylic fluid in the task force 5ton electric splitter?

To add hydraulic fluid to a Task Force 5-ton electric splitter, locate the hydraulic fluid reservoir, which is usually near the pump on the machine. Unscrew the cap and pour the hydraulic fluid into the reservoir slowly to avoid spills. Ensure you are using the correct type and amount of hydraulic fluid as recommended in the machine's manual.


Does a log splitter use hydraulic fluid or hydraulic oil?

Both! The gas engine would take oil then the log splitter that runs the hydraulics would take a specific hydraulic fluid. Its best to go by what the manufacture says


How does a splitter move and function in a hydraulic system?

A splitter in a hydraulic system moves and functions by dividing the hydraulic fluid flow into multiple directions. This allows the system to control the movement of different components, such as cylinders or motors, independently. The splitter directs the flow of hydraulic fluid to different parts of the system, enabling precise and efficient operation.


What is the very first thing to do when servicing a hydraulic fluid system?

A list of Preventive Maintenance Task for a Hydraulic System could be: Change the (could be the return or pressure filter) hydraulic filter. Obtain a hydraulic fluid sample. Filter hydraulic fluid. Check hydraulic actuators. Clean the inside of a hydraulic reservoir. Clean the outside of a hydraulic reservoir.


How do you change hydraulic fluid filter on Massey 2615?

To change the hydraulic fluid filter on a Massey Ferguson 2615, first, ensure the tractor is turned off and parked on a level surface. Locate the hydraulic filter, which is typically positioned near the hydraulic pump. Use an oil filter wrench to remove the old filter, allowing any residual fluid to drain into a pan. Before installing the new filter, apply a small amount of fresh hydraulic fluid to the rubber gasket, then screw it on securely and refill the hydraulic system if necessary.


Were is the hydraulic filter on ford 2000 tractor?

under the seat were do you add the hydraulic fluid


How do you change the hydraulic fluid filter on a Massey Ferguson 275?

where do u put hydraulic fluid in a Massey Ferguson 275


How do you change the hydraulic fluid filter in a Massey Ferguson 165?

To change the hydraulic fluid filter in a Massey Ferguson 165, first, ensure the tractor is turned off and is on a flat surface. Locate the hydraulic filter, typically found near the rear of the tractor, and place a drain pan beneath it to catch any spilled fluid. Unscrew the old filter using an appropriate tool, apply a thin layer of new hydraulic fluid to the rubber gasket of the new filter, and install the new filter by hand until snug. Finally, refill the hydraulic system with the recommended fluid and check for leaks.


What fluid do you use in a Task Force 5 ton electric log splitter when it is under 40 degrees?

In temperatures under 40 degrees Fahrenheit, it is recommended to use a hydraulic fluid with a lower viscosity to ensure smooth operation of the Task Force 5 ton electric log splitter. You can look for a hydraulic fluid that is specified for use in cold weather conditions to prevent issues such as sluggish performance or damage to the equipment.


What hydraulic fluid filter for a 742B bobcat?

It should be 6598903 which crosses over to a Napa Filter 1482


What makes the hydraulic filter blow on a tractor backhoe?

restricted return fluid


Why does my 10.5 ton log splitter blows fluid out vent when piston is retreived?

If your 10.5-ton log splitter is blowing fluid out of the vent when the piston is retracted, it may indicate that the hydraulic system is overfilled or that there is a blockage in the return line. This pressure buildup can force fluid out of the vent. Additionally, a malfunctioning relief valve or damaged seals could also contribute to this issue. It's essential to check the fluid level and inspect the hydraulic components for any signs of wear or blockage.