answersLogoWhite

0

What else can I help you with?

Related Questions

A bottle of 450ml containing 10ppm of colloidal silver Is that means that each ml contains 10ppm?

A bottle of 450ml containing 10ppm of colloidal silver. Is that means that each 1ml contains 10ppm?. Thanks.


How many percent is 10ppm?

0.001%.


How many gallons of ULSD per Metric Ton?

the average density of ULSD is around 0.832 kg/liter or 832 kg/m³ To convert gallons to metric tons, we need to consider the following factors: 1 metric ton = 1,000 kilograms 1 kilogram = 0.001 metric ton 1 liter = 0.001 cubic meter Using the average density of ULSD mentioned above, we can calculate the conversion: Density of ULSD = 0.832 kg/liter Density of ULSD = 832 kg/m³ To convert gallons to cubic meters (m³), we need to know the conversion factor between gallons and liters. There are 3.78541 liters in a gallon. Therefore: 1 gallon ≈ 3.78541 liters Now, let's calculate the conversion: 1 gallon ≈ 3.78541 liters ≈ 0.00378541 m³ Using the density of ULSD, we can determine the volume of 1 metric ton of ULSD: Volume of 1 metric ton of ULSD = (1,000 kg) / (832 kg/m³) ≈ 1.2019 m³ Finally, we can calculate the number of gallons per metric ton of ULSD: 1 metric ton of ULSD ≈ 1.2019 m³ ≈ 1.2019 / 0.00378541 ≈ 317.51 gallons so... there are approximately 317.51 gallons of ULSD per metric ton, using the average density of ULSD as an approximation. Please note that this value may vary slightly depending on the specific density of the ULSD used.


The disadvantage of using biodiesel?

Cost, it's less efficient than ULSD, conversion to biodiesel is expensive, it gels more easily than ULSD does.


How much sodium chloride needed to make 10ppm sodium solution?

2.5 g of Nacl is to be dissolve in 100ml of water gives 10ppm of Na solution.


Why biodiesel is not used commercially?

Because its disadvantages far outweigh its advantages. ULSD motors require expensive conversions to run on biodiesel (contrary to what seems to be popular belief, you don't just pump biodiesel into any ULSD motor without conversion), and it doesn't perform as well as ULSD #2 does.


Can you run a 2008 dodge sprinter with a pdf on ulsd and tranny oil mix?

That would not be recommended,


How do you make 10ppm of NaNO3?

You add water to NaNO3 or NaNo3 to water until you reach the desired concentration


What are the disadvantages of magnetic separation?

costly equipment and more expenaive chemicals.the turbidity should be below 10ppm.


What is the impact of ultra low sulfur fuel on emissions?

Ultra-low Sulfur Diesel (ULSD) Zero Net CO2 Emissions ULSD does not reduce carbon dioxide emissions.• ULSD allows manufacturers to apply to diesel vehicles technologies to control the emission of nitrogen oxides (NOx) and particulate matter (PM) that the presence of too much sulfur would not otherwise permit. Together, ULSD and the technologies are called Clean Diesel.


What twenty six foot box truck is known to run well over 350000 miles?

The length doesn't really tell you anything. For current ULSD fuels, you want a more recent model - ULSD will shorten the longevity of engines manufactured before ULSD (Ultra Low Sulphur Diesel) became a requirement. Other than that, we'd need more specifics as to what you're looking for, what Gross Vehicle Weight Rating you're looking for, etc. You can get a Freightliner M2 with the 6.7 Cummins, and, as long as you do your regular maintenance on it, you should have no problem exceeding 350k.


What is the lethal dose of hydrogen sulfide?

Your body can handle 10ppm (parts per million) for 8 hours. After that you are "hs2 saturated" and you body can't fight it a tenth as well. So to answer your question anything over 10ppm, or anything after 10ppm at 8 hours exposure.