0
For most standard U.S. license plates, you typically need #8 screws that are 3/4 inch to 1 inch long. These screws are usually either Phillips or flat-head, depending on your preference. It's important to ensure that the screws are compatible with your vehicle's mounting holes, and you may also want to check if any specific hardware is recommended by the manufacturer. Always use stainless steel or coated screws to prevent rust.
What else can I help you with?
What size screw is needed to mount license plate on 1998 Cadillac STS?
The size of the screw needed to mount a license plate on a 1998 Cadillac STS is 1/4-inch?æby 1/2-inch. They make license plate kits that includes all needed hardware.
What screw size for Mazda 3 license plate?
The standard screw size for a Mazda 3 license plate is typically a 6mm x 1.0 screw. However, it's always best to check your specific model year, as variations may occur. Additionally, using the correct length screw is important to ensure proper fitment without damaging the vehicle.
What size screw is needed to mount license plate on 2005 ford focus?
1/4" x 20 threads. 1" long.
What size screw is used for the rear license plate c280 mercedes 1996?
based on another thread, this is the info i found. These are the parts indicated on EPC. However, I went to the dealer with these part #s and they are just for the front license plate. Part # 0019904236 (5x12) is somewhat of a sheet metal screw which you need since the front license bracket is a hard plastic material and the holes on there need to be threaded by a sheet metal screw so the license plate itself can be screwed securely onto the bracket. This screw is perfect length if you are mounting your front license plate without a license plate frame. As for part# 0019846429 (5x16) this is a longer screw for mounting the front license bracket to the bumper. Don't need to worry about this one. The license plate screws for the rear are completely different as there is a metal mounting plate adapter that already has pre-threaded holes. You need metric screws M6 1.0 (1.0 is the thread type). Default length is 16mm but you need 10mm if you wish to mount your rear license plate without a license frame otherwise the longer length will drill marks into the rear lid and with a gap between the plate and the screws. I can't find the M6 with 10mm length at my local hardware store. I will need to stick with the ones that came with our car M6 16mm (part# 007985006197) but will need a license frame on it for it to work. I know there's not too much on this matter and no one really cares too much if the screws on your car already work. However, dealers just slap on whatever screws they have on their service bin upon delivery and no one knows what screws you really need for the car. This explains why some folks here complain about loose license plates. Anyhow I have attached both the front (left) and rear screws (right).
License plate bolt size for 2006 mazda3 hatchback?
Use metric 6 mm or 1/4 inch self tapping screw to attach plate. ( North America only )
What size screw is needed to mount license plate on 2004 Honda CRV?
theres no point in putting this question on wiki answers just ask the person at the garage
What number bulb is used on 2001 volkswagon jetta license plate?
License Plate Light Bulb Size: 6418
How do you change license plate bulb in 2001 Cadillac Seville?
If the bulbs are the same as a 2003 Deville, there are two bulb containers above the license plate light and you just need a small screw driver to press in under the left side of the plastic bulb housing to release the plastic clip. The plastic bulb holder will swing from the right hand side and will then fall out. All you need is a medium size flat head screw driver. I had to unscrew the housings with a Philips screw driver and take the housing out of the hole, by turning it sideways and pulling it out. The i turned out the bulb holder from the back of the housing and pulled out the bulb.
What size nut and bolt license plate?
Varies by manufacturer.
What size screw is needed to mount license plate on 2011 Honda CRV?
To mount a license plate on a 2011 Honda CR-V, you typically need 6mm x 1.0 screws, which are often about 20mm long. It's advisable to use stainless steel or zinc-plated screws to prevent rusting. Always check the vehicle's manual or consult a hardware store for specific recommendations if you're uncertain.
What size screws fit Mazda miata license plate?
6mm
What is the license plate bolt size for 2005 Honda accord?
M6x1.00x20mm
