0
You have a large oil leak in the right front of your 1998 Saturn vehicle how do you change the head gasket on this vehicle?
An oil leak there is probably a valve cover gasket leaking. it would not require head gasket replacment. Try tightning the bolts on the valve cover. If that does not work then replace the valve cover gasket.
Yes it could be the head gasket as there are oil passages in the head and i have heard that head gasket on saturns are prone to failure,look around the valve cover for sings of a leak hopfully that's all it is because replacing the head gasket is costly on th 1.9 sohc
What else can I help you with?
How to change the front intake manifold gasket on a 1999 Chevy Venture?
there is no upper intake gasket, only a front and rear
How do you change the front grille?
There are many ways that you could change the front grill of a vehicle. You could replace it or decorate it.
Do you have to pull the motor in a front wheel drive to change a head gasket?
No, the engine doesn't have to come out.
How do you change the front left hub bearing on a 2004 Saturn Ion?
To change the front left hub bearing on a 2004 Saturn Ion, first, lift the vehicle and remove the front wheel. Next, detach the brake caliper and rotor, then remove the axle nut and the hub assembly by taking out the bolts securing it. Replace the old hub bearing with a new one, reassemble all components in reverse order, and ensure everything is securely tightened before lowering the vehicle. Always consult a repair manual for specific torque specs and safety precautions.
How do you change the front differential seals on a 1999 Chevy Suburban?
To change the front differential seals on a 1999 Chevy Suburban, first, lift the vehicle and secure it on jack stands. Remove the front differential cover to access the seals, then carefully pry out the old seals using a seal puller or a similar tool. Clean the sealing surfaces thoroughly before installing the new seals, ensuring they are seated properly. Finally, reassemble the differential cover with a new gasket or sealant, refill with differential fluid, and lower the vehicle.
Where is speed sensor located on 1996 Saturn sl2?
The vehicle speed sensor is between the transmission and the engine from the front of the the engine bay, there is also a vehicle wheel speed sensors in in each tire
Can you flat tow a 1998 sw1 Saturn?
No. I had a Saturn of that year and the handbook warns against it. no front wheel drive vehicle should be flat towed (using a chain or strap). It will damage the transmission, much as towing an AWD or rear wheel drive vehicle without disconnecting the linkage. The best option if towing a front wheel drive vehicle is to use a car dolly, or call for a wrecker or rollback truck.
Where is the oil filter located on a 2008 Saturn astra?
The oil filter on a 2008 Saturn Astra is located in front of the engine. The oil filter can be found on the underside of the exhaust manifold towards the passenger side of the vehicle.
Where is the ambient temperature on a 2003 Saturn L200?
i think its located some where in the front of the vehicle usually by the bumper or by the radiator , caution not in the radiator but maybe attached to it .
How do you change front end wheel bearings in a 2001 Saturn sl?
http://www.saturnfans.com/forums/showthread.php?t=46123
How do you change a transmission front gasket if it is leaking on a 1997 Chrysler Sebring convertible 6 cylinder JX?
Take it to a transmission shop. Depending on what you mean by front gasket, it will probably involve removing the transmission. Again depending on what you mean, it is most likely an indicator of a bigger problem.
How do you replace gasket for 1995 Chevy Tahoe front differential?
To replace the gasket for the front differential of a 1995 Chevy Tahoe, first, ensure the vehicle is securely lifted and supported. Drain the differential fluid and remove the differential cover by unscrewing the bolts. Clean the mating surfaces thoroughly to remove old gasket material, then apply a new gasket or gasket maker as needed before reattaching the cover and refilling the differential with fluid. Finally, torque the bolts to the manufacturer's specifications to ensure a proper seal.
