0
To lube the speedometer cable on a Toyota pickup, first, disconnect the cable from the speedometer and the transmission. Clean the cable thoroughly, then apply a light machine oil or graphite lubricant to the inner cable while twisting it to ensure even distribution. Reinsert the cable into its housing, reconnect it to both ends, and check for smooth operation. Be careful not to over-lubricate, as excess oil can attract dirt and debris.
What else can I help you with?
How do you lube speedometer cable 1989 Toyota truck?
Try blowing graphite down there.
How do you lube a 1983 S-10 4x4 Extended cab speedometer cable?
Remove cable from speedometer head and squirt proper lubricant through cable housing
What component in a 1987 Toyota Tercel speedometer is the most likely to cause the needle to on occasion whir and flip flop erratically?
Either the cable dry or something is wrong in the head. Take the cable out first and lube it and see if that fixes it.
What causes your speedometer to show 90mph while parked And goes up from there when moving 2005 buick?
Speedometer cables can dry out over time. Remove the cable from the back of the speedometer, and lube the cable with graphite. This should fix the issue.
What's the fix for a needle on a 1951 Ford speedometer jumping and making noise?
The cable needs lubricating. Remove the speedometer cable and lubricating it with special lube for that purpose. Any auto parts store can provide the proper lube. Remove the cable and clean it throughly with spray brake cleaner. Let it dry and apply the lube. Reinstall the cable and you should see the needle stop jumping and making noise.
Why is my speedometer bouncing around on my 1993 ford taurus. Only happens over 65 mph.?
Try disconecting the speedometer cable and squirt some lube in it. It might have dried out.
How do you change the Speedometer cable or get it out to try to lubricate it on a 1990 caravan?
Pull the speedo and gauge package out of dash. Unhook wiring. Remove speedo cable from speedometer. Pull speedo cable out of housing, lube it lightly and re-insert. Hook everything back up and re-install gauges. Pull the speedo and gauge package out of dash. Unhook wiring. Remove speedo cable from speedometer. Pull speedo cable out of housing, lube it lightly and re-insert. Hook everything back up and re-install gauges. Pull the speedo and gauge package out of dash. Unhook wiring. Remove speedo cable from speedometer. Pull speedo cable out of housing, lube it lightly and re-insert. Hook everything back up and re-install gauges. Remove gauge package. Remove wires and speedo cable housing. Pull speedo cable out, lightly lube with grease and re-insert. Hook everything back up and re-install gauge packege.
How to change the speedometer cable on a 1990 Honda Gold Wing 1500?
how do you change the speedo cable on a 99 goldwing 1500, and how do you lube the front end/ I need instructions, not parts
How can you stop sqeaky noise in your speedometer?
It's probably a dry cable. Pull the instrument cluster and disconnect the speedometer cable. Squirt some cable lube down the tube. Usually takes a few shots of lube to get enough down the cable to make a difference. Best bet is to squirt a little own the tube and then let it sit for 30 min and come back and do it again. Try 3 or 4 squirts over a couple hours.
Had the rear end rebuilt on your 92 aerostar and now the speedometer fluctuates 5mph Replaced the speed sensor but it still does it When you decelerate the needle is steady?
You need to grease the cable that runs from the speedometer to the trans. (Best to use white lube)
What does it mean when during the first 25-30 MPH your speedometer needle starts to wiggle up and down?
Probably you will need to remove the speedo cable and clean and lube it
What is the best method for properly lubricating a bicycle cable with bicycle cable lube?
To properly lubricate a bicycle cable with bicycle cable lube, the best method is to apply a small amount of lube to the cable where it enters the housing. Then, shift through the gears to help the lube work its way through the cable. Wipe off any excess lube to prevent attracting dirt and debris.
