0
What else can I help you with?
How do you test ignition module 1992 Saturn SL?
Switch parts with another 91-95 Saturn and drive both until completely warmed up to see which car displays any temperature sensitive problems.
How do you replace clutch safety switch on a Saturn?
To replace the clutch safety switch on a Saturn, first ensure the vehicle is in neutral and the ignition is off. Locate the clutch safety switch, typically found near the clutch pedal assembly. Disconnect the wiring harness from the old switch, remove it by unscrewing or unclipping it, then install the new switch in the same position. Finally, reconnect the wiring harness and test the pedal to ensure proper function before starting the vehicle.
1988 dodge D-100 ignition switch linkage adjustment?
To adjust the ignition switch linkage on a 1988 Dodge D-100, first, ensure the vehicle is in the "Off" position. Remove the steering column cover to access the ignition switch and linkage. Loosen the mounting screws for the ignition switch, adjust the linkage until it aligns properly with the ignition cylinder, and then retighten the screws. Finally, reassemble the steering column cover and test the ignition switch for proper operation.
Where is the obd2 connector on a 2008 Saturn astra?
for most Saturn's, the diagnostic test port was below the steering column and a little to the left.
How do you change the ignition switch for a 1995 Cutlass ciera?
To change the ignition switch on a 1995 Cutlass Ciera, start by disconnecting the negative battery cable to ensure safety. Remove the steering column covers by unscrewing the screws, then locate the ignition switch, which is typically mounted on the steering column. Disconnect the wiring harness from the old ignition switch and unbolt it from its position, then replace it with the new switch and reassemble everything in reverse order. Finally, reconnect the battery and test the new ignition switch to ensure it functions correctly.
How do you reset the oil change light on a 1995 525?
Switch ignition on connect LED test lamp between terminal 7 of the diagnostic connector and earth after 3 seconds 5 green LEDs will illuminate Switch ignition off.
How do you replace the ignition on a 1993 Pontiac sunbird?
To replace the ignition on a 1993 Pontiac Sunbird, first disconnect the negative battery cable to ensure safety. Remove the steering column covers to access the ignition switch, then detach the wiring harness and unscrew the ignition switch from the column. Install the new ignition switch by reversing the process, securing it in place, reconnecting the wiring harness, and replacing the steering column covers. Finally, reconnect the battery and test the ignition to ensure it works properly.
How do you replace the ignition switch on a 1993 Ford F150?
To replace the ignition switch on a 1993 Ford F150, first disconnect the negative battery cable to prevent any electrical issues. Remove the steering column cover by unscrewing the screws, then locate the ignition switch, which is usually mounted on the steering column. Disconnect the wiring harness from the old switch, unbolt it, and install the new ignition switch in the reverse order, ensuring everything is securely reconnected before reassembling the column and reconnecting the battery. Finally, test the new switch to ensure it functions properly.
How do you replace the ignition of a 1992 Lincoln Town Car?
To replace Ignition Switch, first you have to remove the old one. To do this you disconnect battery ground cable. Remove the upper steering column shroud by removing the five self-tapping screws. Remove tilt steering column lock lever, Remove lower steering column shroud, disconnect the ignition switch electrical connector, turn ignition switch lock cylinder to the "run" position, remove the two screws retaining ignition switch, and finally unhook the ignition switch from the actuator. Now to install the new one.Make sure that the ignition switch lock cylinder is in the "run" position. You can test for the "run" position by rotating the ignition switch lock cylinder approximately 90 degrees from the "lock" position. Hook up the ignition switch into the actuator. You might have to move the ignition switch slightly back and forth to align the ignition switch mounting holes with the lock cylinder housing threaded holes. Install retaining screws. Connect electrical connector to ignition switch. Connect battery ground cable. Check ignition switch for proper operation, including start and accessory positions. Also, make certain that the column is in the "locked" position. Then Install upper steering column shroud. Install the lower steering column shroud and tilt steering column lock lever.
How can you test the ignition modual?
ignition module on what?
I know its pins 7 and 18 or 19 to reset my oil light on my 325is do you know the correct pins?
Switch ignition on. Connect an LED test light between terminal 7 and earth. After 3 seconds 5 green LEDs will illuminate. Switch ignition off.
How do I reset the oil service light on a 1992 BMW 318i?
Unless you have an LED test lamp the cheapest option is to buy a re set tool from an accessory shop. If you have an LED test lamp Switch ignition on Connect LED test lamp between terminal 7 & earth of the diagnostic connector located on the vehicles inner wing After 3 seconds 5 green LEDs will illuminate switch ignition off
