0
What else can I help you with?
Why would our intake manifold crack on our 2002 Saturn?
This is a common problem for all Saturn S-Series 2000-2002. The plastic intake manifold cracks at the coolant stems, even if the engine does not overheat. This is especially true in the southern half of the US (hotter climate). The intake manifold would need to be replaced, or repaired so no further damage will occur like overheating the engine. CarSaturn of Conyers, GA sells a repair kit to fix this problem- Worked for me. Link is below www.carsaturn.com Good Luck!
Do you have to remove the top half of the intake to change the heather line in the back of the intack?
Yes, to change the heater line in the back of the intake on most vehicles, you typically need to remove the top half of the intake manifold. This is because the heater line is often located in a position that is obstructed by the intake manifold. Removing the top half allows for better access to the heater line for replacement or repair. Always consult your vehicle's service manual for specific instructions related to your model.
Where is the starter located on a 1996 Toyota Corolla 1.6L?
It seems to be directly under the intake manifold, which is closest to the firewall, if you from the drivers side fender you can see about half of it through the holes in the intake manifold
Where is the vacuum switching valve on a 1999 Toyota Tacoma?
in between the intake manifold, bottom half.
How much is labor to replace a knock sensor in a 2001 Yukon XL and where is it located?
The sensor is located under the intake manifold. It takes about 2 and half hours to replace the intake manifold, book time. Knock sensor is about $35 + $60-$90/hr labor. So you are talking about $300.
Where is the Intake Air Temperature Sensor on a 2001 eclipse?
i think u r talking about the MAF sensor or mass air flow sensor which is like half way between the air filter and the intake manifold on the air tube
Can extreme acceleration crack the intake maniford?
I don't know for sure, but I DO know that the intake manifold is a faulty design (thin plastic?? wtf!) which they released an aftermarket replacement for which has METAL on one side. A common problem is a crakced intake manifold on these cars- mine's like that (90% sure) and oil is getting into one side of the spark plugs causing them to crap out needing often replacement. This problem is endemic, if you replace it with the new half-metal manifold it should be fixed. Hopefully!
How do you fix an oil leak for a 1995 Oldsmobile Cutlass Supreme We think it's the o-ring but we're not sure please give all suggestions?
Not sure if this is your problem, but my 1996 Olds Cutlass Supreme leaked coolant into the oil. This was caused by broken intake manifold gasket. Apparently they're somewhat notorious for developing leaks. That repair required taking the top half of the engine apart. Not sure where your leak is, or how much it's leaking, but you may want to consider the intake manifold and head gaskets.
What is the timing order for 75 Chevy half ton?
the firing order is stamped on the intake manifold, it's 1-8-4-3-6-5-7-2
How do you change the spark plugs on a 1997 Jetta?
I have a 1994 jetta. easiest way is to take the intake manifold off using Allen screws. Be sure to catch the gasket between the upper and lower half of the manifold. This gives easy access to all spark plugs.
Where does the fuel line attach to the throttle body of a 1994 s10?
It attaches on the inside of the intake manifold. Tkes the vortec cover off and then the top cover of your intake mainifold. I know it seems wierd but it is actually a two part intake the will seperat in half. you will then see the4 fuel dilivery system and the fuel lines.
Where is the coolant bleed-valve on an r33 gtst?
Ontop of the motor youll see a 9mm (i think) bolt head popping up infront of your intake manifold. Undo half way as it has a slot cut half way up the thread to vent.
