answersLogoWhite

0

P0108 - Manifold Absolute Pressure/Barometric Pressure Circuit High Input
Yes, the MAP sensor may be bad, but check the electrical connection first, if a new one does not fix the issue, and you have ruled out all wiring issues the ECM may be to blame.

User Avatar

Wiki User

10y ago

What else can I help you with?

Related Questions

What is a p0108 trouble code and what to do to fix?

p0108 is map sensor signal high. Replace map sensor


How do you fix P0108 code 2006 Chrysler 300C?

Check all your wiring for your map sensor, if ok replace the map sensor.


2003 buick lesabre error code p0108?

Trouble code P0108 means: MAP Sensor Circuit High Input


1996 buick regal with a p0108 error trouble code?

Trouble code P0108 means: MAP Sensor Circuit High Input


What is code P0108 for dodge gran caravan 1998?

Map sensor fault


What is code for P0108 dodge neon 2000?

Map sensor circuit voltage highMap sensor circuit voltage high


What does diagnostic code P 0108 mean for a 2004 jeep Wrangler 4 cylinder?

P0108 is map sensor volts too high. The map sensor could be bad, or the wiring could be broken. The map sensor bolts to the rear of the intake on the 4cyl.


What is this engine code from a 2005 ford crown victorian SP-TI Intercepter P0108?

The engine code P0108 for a 2005 Ford Crown Victoria Interceptor indicates a problem with the Manifold Absolute Pressure (MAP) sensor circuit. This code typically means that the MAP sensor is reading a voltage that is higher than the expected range, suggesting a potential issue with the sensor itself or its wiring. It can lead to poor engine performance, increased emissions, and fuel economy issues. It's advisable to check the MAP sensor and its connections for faults or damage.


How can i fix these two errors P0106 and P0108 on my diesel ram?

You can try cleaning the map sensor and checking turbo speed sensor.


2005 Nissan exterra map sensor problems?

Replace sensor and clear code.


2005 Chrysler town and country had engine work done now codes are p2074 p0202 p0108 have already reset code for map sensor after installing new map any suggestion on the other codes and how to solve?

P0202 is injector number 2 circuit open. P2074 is map sensor TPS correlation. P0108 is map sensor circuit high. With all three codes I would think the wiring harness has been pinched or damaged near the rear valve cover, driver side.


What does code P0108 mean on chevy?

PO108 Manifold Absolute Pressure Circuit High Input.Can be defective MAP sensor Vacuum leak Short in wiring Loose ground wire

Trending Questions
Which rental car companies rent Toyota Sienna? What strategies can reduce emissions of sulfur oxides and nitrogen oxides to the atmosphere? Can a drunk person in a wheelchair be charged with a DUI or DWI? On a 1997 f 250 how do you reset the abs light so it turns off? Is there a statute of limitations on a DUI charge in Washington State? What exactly is a DUI checkpoint? When is it essential to take measures to help release trapped refrigerant from the compressor oil during recovery? What are the lug nut torque specs for 2013 Hyundai Elantra? What does obd 2 code P0335? What percent of methanal is in washer fluid? If someone's alcohol blood level is 177.1 in a lab report and blood level is based on reference 0-10 in units mg dl what does that make the blood alcohol percentage according to NC DUI DWI law? Which ngk plugs for 1998 explorer? Keenan drove his rental car for 60 miles over a six day period Calculate the cost of renting a car from Rent A Ride if the rental fee is 9.00 per day for six days 0.23 per mile for gasoline and? Will 10 wt oil be ok to use in John deere hydraulic systems? Do you have to strip off old sealer from travertine tiles before you put on new sealer? Why does the PSI sensor keep coming on in your 2006 Chrysler 300 after you put 22 inch rims on it? How long do you get rental car on a compleate loss? How do you get well water stains off of a car? How do you remove oil stains from block paving? The house smells like permanent marker-we turned on the dishwasher last night and it started to smell but none of the walls are hot the outlets don't smell and aren't warm-what is going on?