In general, about half an inch of mortar is required to lay each hollow concrete block. The total amount of mortar needed can be calculated by multiplying this value by the number of blocks to be laid.
As a private installer I charge $1.50 per/sqf ! in Canada !!
You were lying in bed.The way I remember is that objects lay, people lie! Hope this helps!
20 sq. yards is 180 sq. ft. so it will cost you $234.
By being useless you may meen having to be worth something, or in other way, some how helpful to someone or something where useless is just someone who is a bum laying around all the time, never accomplishing anything or always complaining
Location & quality are certainly minimum variablesIn most of the southern and Southwest part of the country expect to pay $1.50-$2.50 per square foot and about $1.00 more I'm Major cities & the north.If the floor is prefinished that is about what you will pay.IF the floor is sand & finish on sight expect to pay at least another $1 per square foot.If the flooring is glued down expect to pay about $70 per pail of adhesive & make sure it is what the flooring maker recommends. If the floor fails & they didn't use the vendors recommended adhesive you are out of luck, no questions asked, game over.If the flooring is Nailed or stapled, again make sure the size, length, and proper gun pressure is used or they will turn down your claim.Different makers have various sub floor requirements so don't assume it is OK to slap it down over whatever is there.Moisture is a tremendous problem with wood floors. In short wood likes water and absorbs it aggressively. Concrete floors suck a lot of moisture from the earth & emit a lot of water to the top side for evaporation. when wood is put over the wet sub floor adhesives fail, wood swells, pops, creaks & generally misbehaves.Engineered wood on concrete floors, solid or engineered wood on suspended wood sub floors.
Concrete block wall construction is typically carried out by laying concrete blocks in a staggered pattern, securing them with mortar. Rebar is often added for reinforcement, and the wall is finished with a smooth surface or decorative veneer.
To create a DIY cinder block outdoor kitchen, start by planning the layout and size of the kitchen. Then, gather the necessary materials such as cinder blocks, concrete mix, and a grill. Begin by laying the cinder blocks in the desired configuration, using concrete mix to secure them in place. Add a countertop and shelves using additional cinder blocks and concrete. Finally, install the grill and any other appliances or accessories you desire.
concreting, concrete pouring, concreting casting.
Not just any sand. Mortar sand. Mortar sand is a larger grain sand that has been washed and screened to remove any rocks or pebbles.
The number of concrete blocks a mason can lay in a day varies based on factors such as skill level, complexity of the project, and working conditions. On average, a skilled mason can lay between 300 to 500 blocks per day. However, this number can be lower for intricate designs or higher for straightforward applications with good weather conditions.
how big are the blocks and how many guys do you have laying them, and how fast and efficient are the workers. do they have to be mortered,
it has to be tacky!!!!!!!
Key considerations when laying the foundation concrete for a building include ensuring the soil is properly compacted, using the right mix of concrete, providing proper reinforcement, and allowing for adequate curing time to ensure strength and stability.
in between existing concrete and the new concrete you need to place an expansion joint in between the two.
To effectively stack cinder blocks for a stable and secure structure, start by leveling the ground and laying a solid foundation. Use mortar between each block to ensure they are securely bonded together. Alternate the direction of the blocks in each layer for added stability. Additionally, consider reinforcing the structure with rebar or concrete fill for extra strength.
The best practices for laying a concrete foundation without using rocks include properly preparing the ground by removing any debris and ensuring it is compacted, using a proper mix of concrete with the right amount of water, reinforcing the foundation with steel rebar, and allowing the concrete to cure properly before building on top of it.
The essential steps for laying concrete slabs effectively are: Prepare the site by clearing and leveling the area. Install a sturdy base, such as gravel or sand, to provide a stable foundation. Create a formwork to contain the concrete and shape the slab. Mix and pour the concrete, ensuring it is evenly spread and leveled. Use a screed to smooth the surface and remove any excess concrete. Allow the concrete to cure and set properly before removing the formwork.