answersLogoWhite

0

What else can I help you with?

Continue Learning about Basic Math

How much weight will a 2x6x10 hold?

The weight a 2x6x10 piece of lumber can hold depends on several factors, including the type of wood, the load type (uniform or concentrated), and how it’s supported. Generally, a 2x6 can support a load of around 40-50 pounds per linear foot when used as a joist in a residential setting. For more specific applications or structural calculations, it's best to consult building codes or a structural engineer.


How many nails are required to hold a 2x6 stud to the plate of a wall that is 8' high?

To secure a 2x6 stud to the top and bottom plates of an 8-foot wall, you typically need a minimum of two nails at each end of the stud, which totals four nails. However, building codes often recommend using three nails per connection for added strength, increasing the total to six nails. Therefore, for optimal stability, you would generally use six nails to hold a 2x6 stud to the plates.


What is the answer for 2x6?

12


How many 2 x 4 16 IOC studs needed for a room that is 224 sf?

depends on your spacing, 16" on center or 24" check your local building codes...and what your deck application is..Are you using a composite decking or wood..Couple of variables play into this...------------------------------------I'll Play:Assuming 16" on center...If you are using 8 foot 2x6's you will need 19.If you are using 12 foot 2x6's over lapping 1 foot to make the 23" and supported along the center of the room you will need 14.For 12" on center: 24(8ft) or 18(12ft)For 24" on center: 13(8ft) or 10(12ft)Note: depending on design/support, 2X6 may not be big enough for code (or safety).


What are the math factor pairs of 12?

1x12, 2x6, 3x4, 4x3, 6x2 1x12 1x12, 2x6, 3x4, 4x3, 6x2 1x12

Related Questions

How much weight a 2x6 hold?

A 2x6 piece of lumber can typically support around 50 pounds per linear foot when used as a horizontal shelf. The actual weight it can hold will depend on various factors such as the type of wood, the length of the span, and the load distribution. It is always best to consult with an engineer or construction professional for specific load-bearing calculations.


What is the maximum weight capacity for a 2x6 span?

The maximum weight capacity for a 2x6 span is typically around 50 pounds per square foot, but it can vary depending on the type of wood and the length of the span.


How much does a 20ft 2X6 weigh?

A 2X6 (dry Douglas fir) weighs 2lbs per foot. Thus a 20ft 2X6 would weigh 40 lbs. Other types of lumber such as pine weighs more and all lumber is heaver when wet or if it has been treated.


How much dead load can an 8' 2x6 hold lying flat Given that it is supported at each end flush with vertical 2x6's at 60 degrees There are 2 Load Bearing points 8 inside each support?

The dead load capacity of an 8' 2x6 lying flat can vary based on factors such as the type of wood, spacing, and load distribution. Typically, a 2x6 can support roughly 40-50 pounds per linear foot when properly supported. Given the specific configuration of the supports and load bearing points, you can expect the 8' 2x6 to hold approximately 320-400 pounds total, but it's essential to consult with structural engineering guidelines for precise calculations. Always consider safety factors and local building codes when determining load capacities.


Will a w-8x18 carry the weight of a basement load wall 2x6 over a 20 ft span?

Yes, a W-8X18 will carry the weight of a basement load wall 2X6 over a 200 feet span.


How much can a 12 foot 2x6 board on edge support?

The load-bearing capacity of a 12-foot 2x6 board on edge depends on several factors, including the type of wood, the spacing of supports, and the load distribution. Generally, a 2x6 made from common softwoods like pine can support approximately 1,000 to 1,500 pounds when properly supported at both ends and loaded uniformly. However, for safety and structural integrity, it's essential to consult local building codes or a structural engineer for specific applications.


What is the answer for 2x6?

12


How many 2x6 inches equal 1 square foot?

1 sq foot = 12in * 12 in = 144 sq in. 144 sq in / 12 sq inches = 12 pieces.


What is evaluate n 7-2x6 when n5?

Evation: n+7-(2x6) Answer: 0


What is the maximum span allowed for 2x6 ceiling joists according to the 2x6 ceiling joist span table?

The maximum span allowed for 2x6 ceiling joists according to the 2x6 ceiling joist span table is typically around 12 feet.


What is the average cost of 2x6x10?

A single 10 foot 2x6 is going to be ~$30 depending on your location. Buying bulk is typically cheaper.


What does 2x6 times 3x2 equal?

It is equal to to 72 because 2x6=12 and 3x2=6 and 12x6=72 or if you think this is to complicated, you can do 2x6=12, 12x3=36, and then 36x2, which then also gives you 72