0
Vaseline, or petroleum jelly, is generally not recommended as a lubricant for O-rings, particularly in applications involving high temperatures or specific chemicals. It can degrade certain materials, potentially leading to O-ring failure. Instead, it's better to use lubricants specifically designed for O-rings, such as silicone-based or PTFE-based greases, which are compatible with a wider range of materials and conditions. Always check compatibility with the O-ring material before use.
What else can I help you with?
Can vaseline be use like a lubricant on o'ring for pump?
Yes, Vaseline can be used as a lubricant for O-rings in pumps, as it provides a good seal and reduces friction. However, it's important to ensure that the Vaseline is compatible with the materials of the O-ring and the fluids involved. For applications involving certain chemicals or high temperatures, specialized lubricants may be more appropriate. Always check the manufacturer's recommendations for the best results.
What do i lubricate pool strainer o-ring with?
Get an O ring lubricant this is available in plumbers supply stores. pool shops automotive spares dealers. I find a bit of Vaseline or other petroleum jelly work quite well also.
Is vaseline good for airsoft guns?
Vaseline can be used as a temporary lubricant for airsoft guns, particularly for O-rings and seals, as it can help reduce friction and prevent wear. However, it’s not ideal for internal components, as it can attract dirt and debris, potentially leading to malfunctions. Specialized airsoft lubricants are recommended for optimal performance and maintenance of the gun. Always check the manufacturer's recommendations before using any lubricant.
Why would the sand filter be leaking where the lid attaches to the tank if you have a new and lubed o-ring?
i believe you trouble is ..........sand...you have to get every little piece of sand off the o-ring and the groove...good luck Also make sure you are using approved Lube. Vaseline can cause a ring to loose its form and cause leaks. There is also the possibility that the lid is warped from age.
Why would the sand filter be leaking where the lid attaches to the tank if you have a new and lubed o ring?
i believe you trouble is ..........sand...you have to get every little piece of sand off the o-ring and the groove...good luck Also make sure you are using approved Lube. Vaseline can cause a ring to loose its form and cause leaks. There is also the possibility that the lid is warped from age.
How do you lubricat o rings?
You can lubricate O-rings by hand. Just make sure you use the correct type of rubber lubricant that is compatible with the O-ring material and what you are trying to seal. Michael Chou Mechanical Engineer http://mykin.com
How do you keep an O ring from becoming dried out?
To keep an O-ring from becoming dried out, store it in a cool, dry place away from direct sunlight and heat sources, as excessive heat can lead to degradation. Using a silicone-based lubricant can also help maintain its moisture and flexibility. Additionally, regularly inspect the O-ring for signs of wear or drying and replace it if necessary to ensure optimal performance.
When was Ring a Ring o' Roses created?
Ring a Ring o' Roses was created in 1881.
When you put in a erring it hurts to o through the hole what do you do to make it better?
vaseline
What does O in O-ring stands for cause ring already known as a round part?
'O' refers not to the shape of the ring but to the ring's cross-section.
On a 1998 blazer wheel bearing assembly where exactly does the large o-ring go?
2000 BLAZER FRONT WHEEL HUB INSTALLATION, WHERE DOES THE LARGE O-RING GO? You can see the outer race of the wheel bearing is stepped. The large o-ring goes over the first step and buts up against the second. The o-ring may be slightly larger than the smaller diameter area on the outer race, fit a little loose, and be a little larger on outside diameter than the larger part of the bearing. The hub needs to be put in evenly. Tighten each bolt a flat at a time if you need to. The o-ring should lubed a little (I used Vaseline). As you tighten the bolts continue to check the o-ring to make sure one part isn't popping out the front or back. The o-ring should rest against the step in the knuckle which corresponds to the bearing. This is not a gasket for the dust shield.
Where does the o ring belong?
Depends on what type of o-ring it is.
