0
What else can I help you with?
What three major products do oil refineries produce?
Gasoline, heating oil and petrochemicals
Does pipe-joint compound contain lead?
No. Clay, vegetable oil, Isopropyl Alcohol, Rosin, Talc, Soybean derivative, and carbon black
What is well stream fluid?
well stream fluid is a term used in oil field engineering.lets consider about the offshore oil field. If the oil reservoir is there beneath the sea bed, then the seabed is drilled and then the pipes are inserted through the drilled sea bed. the fluid (in liquid form because natural gas comes out first) obtained when the pipe reaches the oil reservoir is called as the well stream fluid.
What is the Color code For LPG pipe line?
THE NORMAL CONDITIONS THE COLOUR OF lpg VAPOUR LINE IS GOLDEN YELLOW. BUT THERE IS MANY LINES FOR DIFRENT GASES YOU CAN CHANGE IT & COAD SAPERAT TO SIGN .
Where do you need to build a Oil refinery by the sea?
you don;t, that is probably the worst place to build one because of the pollution it would cause to the ocean and marine animals. +++ That's wrong because it assumes the refinery will be built and run badly, whereas they are normally subject to stringent laws; and while mistakes and accidents in any man-made system can and do occur, the owners do take every precaution to minimise the risks. Refineries are by the sea because many oil and gas reserves are under the sea-bed, and much of the world's oil trade depends on sea transport by pipe or ship.
What is the oil capacity for a 1989 ford mustang 302 engine?
The 1989 Ford Mustang 302 cubic inch engine has an oil capacity of 4 quarts. The engine oil should be changed every 7000 miles or every three months.
What is the oil capacity of a 1978 Trans Am?
The 1978 Pontiac Firebird Trans Am engine oil capacity is five quarts. The 305, 350, and the 454 cubic inch motors all had the same motor oil capacity.
What is the oil capacity of a 96 cu inch Harley Davidson?
3 quarts
What is the oil capacity for a 289 cubic inch Ford engine?
The engine oil capacity in a 289 CID in a Ford passenger car would be 5 qts with oil filter change.
What is the Oil capacity of a ford 8 inch rear end?
4gl
What are the steps to thread iron pipe?
You use a Die to cut the threads. A Die is like a nut for a bolt. It is designed to screw onto the end of the pipe and cut the threads. Clamp the pipe so that it cannot turn, start the die on the pipe while putting oil on the pipe. There is special thread cutting oil but any motor oil will work. This make the cutting easier. Cut about 1 inch of threads on the pipe. Make a couple of turn and back the die up a half of a turn. Do this until you have an inch of thread. Backing the die up gets the shavings out of the cutting grooves. The new threads will be very sharp and will cut if you wipe the oil off with your hand, use a rag. The dies are sized for the size of pipe, 1/2, 3/4 and 1 inch are the most common.
What is the oil capacity for a 1979 9 14 inch Chrysler differential?
Aprox 5 pints
Oil capacity 1995 wide glide?
Three quarts.
What is the oil capacity for a 1975 Kawasaki 400?
The 1975 Kawasaki 400 engine oil capacity is three pints. The manufacturer recommends that you never overfill the motor oil.
How many gallons will flow through a 12 inch pipe at 50psi?
That depends entirely on the viscosity of the liquid in the pipe ! Water would flow faster than oil !
What is the oil capacity of a Bobcat 763 skid steer?
The motor oil capacity of a Bobcat 763 skid steer is four quarts. The Bobcat 763 skid steer hydraulic oil capacity is three gallons.
What is the oil capacity for a 1989 jeep wrangler 253 cubic inch 6-cylinder?
6 quarts
