A tangentially fired boiler has between 4 and 8 burners, placed in the corners of the boiler. These are sometimes angled vertically to maximize impingement of the flames. They are fired into the center of the boiler, not directly into the center, but at the wall to adjacent to them. This causes the flames to swirl inside of the boiler, causing an even distribution of flame throughout the boiler. This is shown pretty well here: http://www.alstom.com/power/coal-oil/utility-boilers/firing-systems This website also has a lot more detail than previously provided.
For getting better efficiency from boiler, coal is pulverized in mills (powder form) before entering into boiler along with hot air. This is done in order to control damage to boiler tubes and plates due to high (but cheap) sulphur content in coal. These types of boiler are usually called super critical boiler and works on high pressure (3600psi) and temperature (610 degree C) unlike sub critical boilers. alok bh.
All boilers are made to a pressure specification and in most countries any pressure vessel over a certain size is required to be periodically inspected and pressure tested to ensure it is fit for purpose. In addition to being in sound condition, the boiler is also expected to have some form of pressure relief valve. This is of sufficient size to vent off excess pressure before it gets to an explosive situation. It is obviously important that the pressure of this device is set to a lower level than the ultimate pressure specification of the boiler. Even quite small boilers, like those in coffee makers need to be inspected. Some boilers are 'gas fired' such as home heating boilers. These have a device called a thermocouple that detects the flame and is linked to the gas valve. If the flame goes out, or the burner does not ignite when gas is released in the boiler, it will shut the gas off. Typically gas fired boilers have a number of devices that will shut off the gas in the event that something doesn't work. This means that if the gas supply pipe is in sound condition, the boiler itself cannot leak gas and cause an explosion.
35% efficiency
The following extract taken from an article by Ingo Paul in Energy Issues No 19 April 1999 published by the World Bank [external link] briefly describes the difference between a subcritical and a supercritical boiler. "Supercritical" is a thermodynamic expression describing the state of a substance where there is no clear distinction between the liquid and the gaseous phase (i.e. they are a homogenous fluid). Water reaches this state at a pressure above 22.1 megapascals (MPa) The "efficiency" of the thermodynamic process of a coal fired power (sic) describes how much of the energy fed into the cycle is converted into electrical energy. The greater the output of electrical energy for a given amount of energy input, the higher the efficiency. If the energy input to the cycle is kept constant, the output can be increased by selecting elevated pressures and temperatures for the water-steam cycle. Up to an operating pressure of around 19 MPa in the evaporator part of the boiler, the cycle is sub-critical. This means, that there is a non-homogeneous mixture of water and steam in the evaporator part of the boiler. In this case a drum-type boiler is used because the steam needs to be separated from water in the drum of the boiler before it is superheated and led into the turbine. Above an operating pressure of 22.1 MPa in the evaporator part of the boiler, the cycle is supercritical. The cycle medium is a single phase fluid with homogeneous properties and there is no need to separate steam from water in a drum. Once-through boilers are therefore used in supercritical cycles. www.whizkris.com
Well when I hear the word "Fired" used in reference to a boiler, it is used to describe the type of fuel used to heat the boiler (to fire it) such as a "Coal fired" or "Gas fired"
Its a Boiler that is fitted with two or more heating sources. Say Gas and Oil Fired
a boiler (a device for heating water) that is powered by gas
externally fired
Cold
A gas fired boiler is a product used to heat your water for homes as well as swimming pools, they are very ifficient and save energy thus lowering your electric bill. There is a down side to having a gas fired boiler being as the costs of gases has gone up greatly it would be harder to keep a gas fired boiler going for a middle class person
A tangentially fired boiler has between 4 and 8 burners, placed in the corners of the boiler. These are sometimes angled vertically to maximize impingement of the flames. They are fired into the center of the boiler, not directly into the center, but at the wall to adjacent to them. This causes the flames to swirl inside of the boiler, causing an even distribution of flame throughout the boiler. This is shown pretty well here: http://www.alstom.com/power/coal-oil/utility-boilers/firing-systems This website also has a lot more detail than previously provided.
wholly or partly surrounded by water
gas fired the boiler
form_title=Boiler & Radiator Heating Installation form_header=7033 Do you want additional thermostatic controls in certain rooms?*= () Yes () No Would you like to know more about the project's green alternatives ?*= () Yes () No Please specify the type of boiler system to be installed.*= () Natural gas fired () Propane gas fired () Oil fired () Electric fired () Want Recommendation
I like Weil-Mclain or Peerless.
An oil-fired boiler is a modern way to heat a home the old-fashioned way. One of the largest manufacturers Weil-McLain sells boilers for residential or commercial needs.