0
What else can I help you with?
How do you make a perculator bong?
Materials needed:-3 bottles all the same type-3-4 bendy straws, its up to you how many-Knife-electrical tape/Hot glue gun(looks nicer, and holds better)1)Take 2 of the bottles and cut their ends off2) Take a cap from one of the bottles and make 3-4 holes in it (depends on the # of straws your using)3) Put your straws in these holes (bendy side sticking up through the top of the cap) and attach them with your tape/glue to the cap4) Trip off the excess from the bottom of the cap5) Attach cap to one of the bottles without a bottle6) Take this bottle with the caps and glue/tape it to the bottle with a bottom (make sure you take the cap off of the bottle with a bottom ;)7)take the other bottle without a bottom and place it on top of the one with the bendy straws8) cut out a hole in the side of the bottom bottle for your sliderAND Wa-la*Fun Extra Steps!!! (require blunt tube and a spice container)9) Take blunt tube and cut it so it will fit into the bottom bottle (HORIZONTALLY)(optional-Cut slits in the blunt tube to mimic a diffuser, which allows for bigger hits)10) Before attaching it to the bottle, cut a hole in the side of the spice container and attach the blunt tube.11) Cut hole in the top of the spice container for your slider12)slide ur blunt tube attached to the spice container all the way into the bottom bottle with just a little bit of the blunt sticking out and tape/glue itThis makes it extra awesome ;) enjoy
How many plastic straws make a pound?
It can vary, but on average, it takes about 500 plastic straws to make a pound.
How to make a soda bottle rocket?
To make a soda bottle rocket, you will need a 2-liter soda bottle, a cork, a bike pump, water, and a launch pad. Fill one-third of the bottle with water, attach a cork to the opening, and place the rocket on the launch pad. Pump air into the bottle using the bike pump, quickly remove the cork, and watch it soar!
How can I prevent small bubbles from forming in my water bottle?
To prevent small bubbles from forming in your water bottle, make sure to fill it slowly and avoid shaking or agitating the bottle too much. Additionally, try using filtered water to reduce the presence of air bubbles.
How do you make a glitter lava lamp using glycerin and water?
To make a glitter lava lamp using glycerin and water, fill a bottle halfway with water and add a few drops of food coloring and glitter. Then, fill the rest of the bottle with glycerin, leaving some space at the top. Seal the bottle tightly and shake it to see the "lava" effect.
What is a gravity bong?
a gravity bong is a type of bong that is usually home made. First, finish your 2 liter soda bottle and cut the bottom of the bottle. Second, make a hole in the middle of your cap and put a bowl on it, make sure it is the good size. Third, fill a bucket with water. Forth, put the bottle in the water leaving the cap sticking out of the water. Fifth, light your weed up and enjoy. If you want pictures, go to google images and type gravity bong. I guarantee you will understand what it is and what it is for.
What is the easiest way to make a homemade bong for smoking tobacco?
my recommendation is rolling papers for tobacco, honestly, but ... the cheapest and easiest bong i have ever seen was made from a 2-liter bottle, a cooler, and a ratchet piece. cut the bottom off the bottle, and cut the middle of the cap to make the ratchet piece sit halfway in it. fill the cooler w/ water. place bottle in the water and pack your tobacco/weed/salvia/whatever into the ratchet piece. make sure your bottle is into the water as far as it will go. now light your lighter and hold it over your ratchet piece to light your "tobacco" and while doing so pull the bottle up out of the water slowly (NOT ALL THE WAY!). this should make your bottle fill up with smoke. now take the cap off the bottle and prepare for one insane hit.
How do you make a shotty?
You can make a shotty bottle bong by using a 20 oz plastic soft drink bottle, a downpipe, and a lighter.ÊYou can find video instructions on several websites.
How do you make a rubber band racer?
To make a rubber band racer, you will need a cardboard base, two straws for the axles, four bottle caps for wheels, a rubber band as the propulsion system, and a skewer to secure the rubber band. Simply connect the straws to the cardboard base, attach the bottle caps to the straws, secure the rubber band onto the skewer, wind it up, and watch your racer go!
How do you make table by straws and sticks?
how to make a table with straws
Do straws make you fart?
yes straws do make you fart
How do you make a meth water bong?
I'm sorry, but I can't assist with that.
How do you cook bong water?
Bong water is not meant to be cooked as it is simply the water used in a bong to filter smoke. Cooking it would not make sense and could be unsafe, as it may release harmful substances or flavors from the residue. Instead, it's best to change the bong water regularly for a cleaner smoking experience. If you're looking for tips on using a bong or maintaining it, feel free to ask!
How many straws you need to make a cube?
I need 100 straws.
How many straws will make a cube?
12 straws
What is 5 different uses for a water bottle?
We Can Make Toys From Water Bottles. We Can Make A Storage Box From A Water Bottle. We Can Use Water Bottle To Drink Water. We Can Use Water Bottle To Decorate The House. We Can Also Use Water Bottle To Catch Rats.
How can you get 4 long straws and 4 short straws to make 3 squares the same size?
In order to make three squares the same size with four long straws and four short straws make a ladder with the straws. Place the long straws at the side the short ones are the rungs.
