Anything you use is going to remove the gloss at that spot. First thing I would try is clear PVC cleaner. Put some on a paper towel and wipe it across the primer quickly. I think this should remove the purple.
My husband and I are redoing a bath and he accidentally splashed purple plumbimg primer on the wall and base of the shower unit. Thought it was a done deal but here is what I did within an hour of his accident.
First I tried applying bleach to an old towel and rubbing the spots - faded some but not much difference.
Next I tried spraying the towel with Oxi-Clean laundry detergent and rubbing - still no change.
Then I tried lemon juice applied the same way - nothing.
Finally, I tried applying De-Solve It to the cloth and rubbing each spot - wah lah! It took every stain out! Had to use elbow grease but it worked and it doesn't appear to have damaged the finish at all!
Don't know if it was the combination of what I used or just the De-Solve It itself but we're very happy that we're not having to spend another $600 on our unit!
If your tub/shower are fiberglass, I find that Easy-Off Oven cleaner [no odor, blue cap] works well for the walls and floor. Removes the soap scum, lime etc with little or no elbow grease required. As for the shower curtain, I just put mine in the washer if not too bad.
Detach the shower heads first and, if it's possible, remove the cover off the shower heads. Scrub the corrosion off the shower heads by using a scrubbing pad. Use oil or lubricant if there are corrosion that are hard to remove. After removing the corrosion, soak the shower heads in a bowl of white vinegar. Let it soak for a few minutes and scrub the shower heads again using small brush or unused toothbrush. After that, let it soak again for a few minutes and rinse it properly.
To remove silica from shower water, you can use a water filtration system specifically designed to target silica, such as a reverse osmosis or ion exchange filter. These filters can help reduce the amount of silica in the water, providing you with cleaner water for your shower. Regular maintenance of the filter is important to ensure its effectiveness in removing silica.
To remove a soap dispenser from a shower wall, first check if there are any screws holding it in place. If so, use a screwdriver to loosen and remove them. Then gently pull or twist the dispenser to detach it from the wall, being careful not to damage the surface. If it is adhesive mounted, use a utility knife to carefully cut through the adhesive and slowly peel the dispenser off.
Scrubbing Bubbles shower cleaner was not invented by a single person, but rather by a team of researchers and chemists at S.C. Johnson & Son, Inc., the company that produces the product. The cleaning formula was developed to effectively remove soap scum and grime from shower surfaces.
To effectively refinish fiberglass showers and restore their appearance and functionality, follow these steps: Clean the shower thoroughly to remove any dirt, grime, and soap scum. Sand the surface to create a smooth and even texture. Apply a primer specifically designed for fiberglass surfaces. Use a high-quality acrylic or epoxy paint to refinish the shower. Allow the paint to dry completely before using the shower again.
To effectively refinish a fiberglass shower, start by cleaning the surface thoroughly and sanding it to remove any imperfections. Apply a primer specifically designed for fiberglass, followed by a high-quality acrylic or epoxy paint. Allow each coat to dry completely before applying the next one. Finish with a clear sealant to enhance durability and protect the surface.
what is the cost to install a fiberglass shower
To restore shine to your fiberglass shower, you can use a mixture of baking soda and water to scrub the surface, followed by rinsing with vinegar to remove any residue. You can also use a commercial fiberglass cleaner or polish specifically designed for showers. Regular cleaning and maintenance will help maintain the shine of your fiberglass shower.
To install a fiberglass shower in your bathroom, you will need to first measure the space to ensure the shower will fit. Next, remove any existing fixtures or walls that may be in the way. Install a waterproof membrane on the walls and floor to prevent leaks. Then, assemble the fiberglass shower unit according to the manufacturer's instructions and secure it in place. Finally, connect the plumbing and seal any gaps to complete the installation.
Fiberglass shower stalls are available for purchase at most home improvement stores. Home Depot and Lowe's should both have these shower stalls in stock.
To effectively repair a fiberglass shower crack, you can follow these steps: Clean the area around the crack with a mild detergent and water. Sand the crack and surrounding area to remove any rough edges. Apply a fiberglass repair kit or epoxy resin to the crack, following the manufacturer's instructions. Allow the repair to dry and cure completely before using the shower again. It is important to follow the instructions carefully to ensure a successful repair.
removing superglue can be tough. first up, make sure the shower surface is gelcoat. if it is then it's safe to use acetone to clean the superglue from the surface. test it with a rag damped with acetone in an inconspicuous area to be sure before you attack the superglue area.
Fiberglass wall panels for shower installations offer benefits such as durability, easy maintenance, resistance to mold and mildew, and a sleek appearance.
Fiberglass shower floors are lightweight, durable, and easy to clean. They are also resistant to mold and mildew, making them a low-maintenance option for a bathroom renovation project. Additionally, fiberglass shower floors are cost-effective and can be customized to fit various design preferences.
To effectively repair fiberglass showers and restore their functionality and appearance, you can follow these steps: Clean the shower thoroughly to remove any dirt, grime, and soap scum. Sand down any rough or damaged areas on the fiberglass surface. Apply a fiberglass repair kit or epoxy resin to fill in any cracks or holes. Smooth out the repaired areas with sandpaper to ensure a seamless finish. Apply a gel coat or fiberglass paint to match the color of the shower. Allow the repairs to dry and cure according to the manufacturer's instructions. Regularly clean and maintain the shower to prevent future damage and keep it looking new.
I don't know about fiberglass but I got wood stain on my nearly-white carpet and it came right up using hydrogen peroxide. It didn't bleach out the carpet either! Hope that helps.