The gas orfice when operating creates a vacuum drawing combustion air into the burner. This is the reason that gas pressures vary between types. Natural gas appliances operate at a nominal 3.5" wc pressure, while LP appliances run 10-11" wc. Natural gas has about 1000 btu's per cubic foot, while LP gas has about 2500. As an example, if you were to reduce the manifold pressure of LPG, you would have an oxygen starved mixture that would not burn properly. lc
No, burning a log in a fireplace will not effectively remove soot buildup. Soot is best removed by cleaning the fireplace using appropriate tools and methods recommended for the specific type of fireplace and soot buildup.
Chimney is to fireplace as faucet is to bathtub. Just like a fireplace needs a chimney to function properly, a bathtub needs a faucet to fill it with water. Both pairs are essential components that work together to achieve a specific purpose.
There are two components to the mix-o-vial: the top chamber holding water, or some other solute, and the bottom chamber holding the medication, usually in a powder. There's a rubber stopper between the two chambers, with a small needle at the bottom of the top chamber. To activate the mix-o-vial, you squeeze the top and bottom together. This pushes the needle through the rubber stopper and allows the water to drain into the bottom chamber. The vial is then vigorously shaken to dissolve the medication.
Yes, you can replace gas logs with lava rocks in your fireplace. Lava rocks can provide a more natural look and feel compared to gas logs. However, make sure to check with a professional to ensure that your fireplace is suitable for burning with lava rocks and to ensure proper ventilation.
A fireplace insert is a self-contained unit that is installed into an existing fireplace to enhance efficiency. It works by creating a closed combustion system that traps and circulates warm air around the insert, radiating heat into the room. This helps increase the heating efficiency of the fireplace and reduces heat loss up the chimney.
fireplace dont work
Yes, lower prices fireplace mantels do indeed work as efficiently as higher priced fireplace materials. There is not a lot of difference.
it burns the wood
Do fireplace maintenance service companies work on gas fireplaces also? I think I have a leak, as I smell gas when I turn my fireplace on.
form_title= Corner Fireplace form_header= Relax with a corner fireplace. Are you repairing an existing fireplace?*= () Yes () No Do you want a gas fireplace?*= () Yes () No What type of backsplash would you like?*= _ [50]
You can install a custom fireplace screen over an existing fireplace. It is not recommended to put a new screen over an old screen. The main thing you need when planning on a new screen is the exact measurements of the fireplace.
Magma Chamber: underground pocket of molten rock
The chances are the flint chamber is blocked with old flint ,try to remove with a pin ,if this fails you will need to dismantle the ligter to unblock it. good luck
It really all depends on the type of Fireplace you have. Fireplaces usually run on a pilot with a thermocouple or thermopile. These produce their own milivolts to run the gas valve. These type of fireplaces do not need power to ignite. If the fireplace's on/off switch is a remote that runs off of batteries or is a switch on the faceplate of the fireplace, then this fireplace should work with no power. Most fireplaces have a blower that circulates the warm air it generates. This fan would be running on 120v from the street and would not work when the power goes out. You may still have a flame on, but all the heat it generates is going out the stack. Other fireplaces have no fan and are mainly for looks. You may have a fireplace that is dependent on the 120volts and will do nothing. Check the operation manual on your fireplace.
A fireplace blower is a device that helps to improve the efficiency of a fireplace by circulating warm air throughout the room. It works by drawing in cool air from the room, passing it over the hot surface of the fireplace, and then blowing the warmed air back into the room. This helps to distribute heat more evenly and effectively, making the fireplace more efficient at heating the space.
To work a fireplace effectively and safely, follow these steps: Make sure the chimney is clean and clear of debris. Use dry, seasoned wood for a cleaner burn. Open the damper before lighting a fire to allow for proper ventilation. Use a fireplace screen to prevent sparks from escaping. Never leave a fire unattended and always extinguish it before going to bed. Keep flammable items away from the fireplace. Install carbon monoxide and smoke detectors near the fireplace. Have the fireplace inspected and cleaned annually by a professional.
Check the fuse first. If the fuse if good then either the lighter itself or the lighter outlet is defective.