Kilogram is the unit of mass. But unit of weight will be either kg wt or newton.
One kg of iron would weigh one kg wt. One kg wt = g newton
Here g is acceleration due to gravity. g = 9.8 ms--2
So one kg of iron weighs 9.8 newton
The density of copper is 8940 kilograms per cubic meter.
7874 kg/m^3 is the official density of iron; many times (when accuracy is not important) I round to either 7900 or 8000 kg/m^3.
A liter of iron weighs about 7.7 kg
7830kg/m3.
10kg
k.kl;
Silver is more dense because silver is around 10.5g/cc, an iron around 7g/cc. silver atomic number 47, where as iron is 26. This means the nucleus will be much heavier, but also take up more space.
Iron is more dense than silicon.
The number listed most frequently on the www for the density of pure iron at room temperature is 7.874 grams of mass per cubic centimeter. On Earth, 7.874 grams of mass weighs 0.0772 newtons (rounded), or 0.278 ounce avdp.
Copper has a density of 8.9 g/cm3 while iron has a density of 7.9 g/cm3. Therefore copper is denser than iron.
Iron has a density of approximately 7.86g/cm3. Nails are not usually made from pure iron, but from soft steel, a mixture of iron and carbon. The density, however, is pretty much the same depending on the grade of steel used.
Iron has a greater density.
The weight of 1 mm thick x 1000 mm x 1000 mm galvanized iron sheet is 7.85 kilogram. This is based on taking the density of the iron sheet to be 7850kg per cubic meter.
The density of iron is rho = 7,860 kg/m³ or rho = 7.86 g/cm³.
This is a trick question, right? Regardless of the substance , if they weigh the same, they have the same weight. What is different is the density of sbustances. For instance a cubic foot of Helium weighs less than a cubic foot of carbon dioxide. A cubic foot of iron weighs more than a cubic foot of aluminum. If you visit the web site http://www.chemicalelements.com you can look up the density of many substances that are called elements.
A galvanized iron is similar to steel; it is material that composed of cold-rolled and hot-dip galvanized mild steel. It has 7850 kilograms per cubic meter density same as a steel.
The average weight of iron per cubic meter is 2500 kilograms. Therefore 46 cubic meters of iron equal to 115 tons in mass (115 000 kilograms). However, the density of iron varies. There are conversion tables on internet. If you know the density of ore-iron it will become easier to find out the volume to mass ratio more accurately.
Any amount of lead has the same density as one cubic centimeter of lead, but no amount of lead has the same density as any amount of iron.
The amount of material (in kilo grams) will occupy the volume of one cubic meter. it is approximately 2.2t/m3 for pellets.
7,874 kg
You can find the volume of 500 grams of iron by using the formula for density and knowing iron's density. The density of iron is 7.85 grams per cubic centimeters and the formula for density is ggiven by mass divided by volume, or volume is equal to mass divided by density. The volume is 500 grams/ 7.85 grams per cubic centimeters, which is 63.69 cubic centimeters.
The density of iron is 7,874 kg/m3 or 7.874 g/cm3. The density of iron filing is somewhat lower depending upon how fine the filings are, but I guess more than 4000 kg/m3 or 4.0 g/cm3. The SI standard of density is measured in kg/m3. The density of a material is defined as its mass per unit volume. The density of iron does not change with the size of the sample. A bucket full of iron filings will have a lower density than the block because there will be air between the individual filings. The density of a deep pile of filings will be greater than a thin pile because the weight of the filings above compacts the filings below by pushing out some of the air. However, the density of each individual piece will still be the same as for the whole block.
0.26 lbs/ cubic inch