answersLogoWhite

0

One method to separate iron fillings from sand is by using a magnet. The iron fillings are attracted to the magnet and can be easily separated from the sand.

User Avatar

AnswerBot

1y ago

What else can I help you with?

Continue Learning about Chemistry

How could you separate a mixture of iron fillings and sulfur powder?

One method is to use a magnet to separate the iron fillings from the sulfur powder, as iron is magnetic but sulfur is not. Another method is to mix the mixture with a solvent that dissolves the sulfur powder, leaving the iron fillings behind. Lastly, heating the mixture can also cause the sulfur to sublimate, leaving the iron fillings behind.


How could you separate sawdust and iron fillings in a solution?

You can use a magnet to attract and separate the iron fillings from the sawdust. Place the magnet in the mixture and move it around to attract the iron fillings. The sawdust will not be affected by the magnet and can be separated from the iron fillings.


How do you separate copper fillings from a mixture of copper fillings and iron fillings?

One way to separate copper filings from a mixture of copper and iron filings is by using a magnet. Since iron filings are attracted to magnets while copper filings are not, you can use a magnet to pull out the iron filings, leaving the copper filings behind.


Could you Devise the experiment that will allow you to separate mixture of copper fillings and salt?

1 take the mixture of salt and sand and immerse them in water. 2 run the water and sand through a filter that separates out the sand. 3 store the sand. 4 boil the water until it has all evaporated or just wait for it to evaporate naturally. This will leave a residue on the bottom of the container which Will be the salt


How do you separate oxygen ammonia hydrogen mixture?

Various methods could be used to separate such a mixture. However, one suitable method which is widely used for separating gas mixtures is fractional condensation. This method relies on differences in boiling points to separate the components.

Related Questions

How could you separate a mixture of iron fillings and sulfur powder?

One method is to use a magnet to separate the iron fillings from the sulfur powder, as iron is magnetic but sulfur is not. Another method is to mix the mixture with a solvent that dissolves the sulfur powder, leaving the iron fillings behind. Lastly, heating the mixture can also cause the sulfur to sublimate, leaving the iron fillings behind.


What are the two method that can be use to separate a mixture of iodine crystal and iron fillings?

Since lead iodide is insoluble in an aqueous solution, you could filter it out using a funnel and filter paper.


If you have a mixture of gravel and sand and salt and iron fillings what properties of these substances could you use to separate the mixture and how would you use those properties?

You could use a magnet to separate the iron fillings from the mixture, as iron is magnetic while the other substances are not. Next, you could use water to dissolve the salt, allowing you to separate it from the sand and gravel mixture. Finally, you could use a sieve to separate the remaining sand and gravel mixture based on particle size.


What is the separation technique that you need to use to separate steel fillings from sulfur?

You can use a magnet to separate steel fillings from sulfur because steel is magnetic whereas sulfur is not. By passing a magnet over the mixture, the steel fillings will be attracted to the magnet and can be easily separated from the sulfur.


If you made a mixture of iron fillings and salt how could you separate that mixture into its 2 original substances?

Place the mixture in water. You recover the iron once the salt dissolves. Then allow the water salt mixture to dry and allow salt crystals to reform.


How could you separate aluminum fillings from iron fillings?

Very easily, put a magnet on them it will attract the iron but not the aluminium.


How could you separate sawdust and iron fillings in a solution?

You can use a magnet to attract and separate the iron fillings from the sawdust. Place the magnet in the mixture and move it around to attract the iron fillings. The sawdust will not be affected by the magnet and can be separated from the iron fillings.


How do you separate copper fillings from a mixture of copper fillings and iron fillings?

One way to separate copper filings from a mixture of copper and iron filings is by using a magnet. Since iron filings are attracted to magnets while copper filings are not, you can use a magnet to pull out the iron filings, leaving the copper filings behind.


Could you Devise the experiment that will allow you to separate mixture of copper fillings and salt?

1 take the mixture of salt and sand and immerse them in water. 2 run the water and sand through a filter that separates out the sand. 3 store the sand. 4 boil the water until it has all evaporated or just wait for it to evaporate naturally. This will leave a residue on the bottom of the container which Will be the salt


How could you separate iron fillings from sand?

With a magnet : only iron will be attracted.


How could you separate the components of a charcoal and sugar?

To separate charcoal and sugar, one method could involve adding water to the mixture and stirring, which would dissolve the sugar but leave the charcoal behind. Next, the mixture could be filtered to separate the dissolved sugar solution from the charcoal residue. Finally, the water could be evaporated to retrieve the sugar.


I have a mixture of sand and water. What is a method that could be use to separate the mixture?

You can use the process of filtration to separate the sand and water mixture. By passing the mixture through a filter paper or a sieve, the sand particles will be retained while the water passes through. This method relies on the differences in particle sizes between the sand and water.