0
I was exposed 10 yrs ago, supposedly acute chemical pneumonitis, but i am having ( and for past ten years ) chronic lung infections, repeated and worsening chronic bronchitis and pneumonia, Asthma attacks (although i did have childhood asthma that had not bothered me except if seriously ill for oh 20 years prior to exposure) i just recently spent a week in hospital in respitory unit on oxygen etc., and reopening my claim has been denied.
So I strongly suggest that you get and follow medical advice (obviously) and treatment, RECORD EVERYTHING, EVERY TIME YOU GO TO A DOCTOR FROM NOW ON. And start researching now, that is what i am doing. There are many conditions that have very similar symptoms and are more common , make sure you are properly treated and diagnosed from here on out.
What else can I help you with?
Which part of the procedure calls for 3 M and which part of 9 M sulfuric acid?
The procedure calls for using 3 M sulfuric acid during the preparation of the standard solutions, as it is less concentrated. The 9 M sulfuric acid is typically used during the extraction or digestion steps that require a stronger acid for efficient reaction.
What are the steps to prepare M sulphuric acid?
To prepare 1 M sulfuric acid (H2SO4), you would need to dilute concentrated sulfuric acid to the desired molarity. Calculate the volume of concentrated sulfuric acid needed based on its concentration (typically around 18 M) and the final volume required. Always add acid to water slowly with stirring and proper safety equipment due to the exothermic nature of dilution and the corrosive properties of sulfuric acid. Dilute to the final volume with distilled water.
Calculate the number of moles of hydrogen atoms in 4.75 mol sulfuric acid.?
4.75 moles H2SO4 (2 mole H/1 mole H2SO4)(6.022 X 1023/1 mole H)(1 mole H atoms/6.022 X 1023) = 9.67 moles of hydrogen atoms ------------------------------------------ As you can see this set up is formal as the two last steps are superfluous when Avogadro's number actually apears over itself as a form of 1.
How is fluorescein synthesized?
Fluorescein is synthesized through a series of chemical reactions starting with phthalic anhydride and resorcinol. These compounds are heated together with sulfuric acid to form fluorescein. The process involves multiple steps and careful control of reaction conditions to ensure the desired product is obtained.
How stearic acid convert into ethyl stearate?
Mix Ethanol with Stearic Acid, use Sulfuric Acid as catalyst. Sulfuric Acid can be pre-diluted into the Ethanol. Boil the mixture under reflux. may need to do a few times after each reaction cycle, to use water to wash out the access ethanol & reaction by-product = water. Then re do the same, mix ethanol+sulfuric acid into the partial reactants (Stearic acid + Ethyl stearate) to fully convert the Stearic acid into Ethyl stearate.
What are the 2 steps in respiraton?
The two main steps in respiration are called glycolysis and aerobic respiration. Glycolysis occurs in the cytoplasm and involves breaking down glucose into pyruvate. Aerobic respiration then takes place in the mitochondria, where pyruvate is further broken down in the presence of oxygen to produce ATP.
What are the steps to wound healing?
Acute wounds in an animal model shows that four basic steps are involved in wound healing. Hemostasis, inflammation, proliferation or Granulation and remodeling or Maturation.
Which part of the procedure calls for 3 M and which part of 9 M sulfuric acid?
The procedure calls for using 3 M sulfuric acid during the preparation of the standard solutions, as it is less concentrated. The 9 M sulfuric acid is typically used during the extraction or digestion steps that require a stronger acid for efficient reaction.
When recording the steps of a job what should be done regarding steps that may not be performed every time the job is accomplished?
the steps should be included
What are the 4 different steps at which heme biosynthesis defects occur with acute porphyrias?
ALA dehydratase deficiency porphyria (step 2); acute intermittent porphyria (step 3); hereditary coproporphyria (step 6); variegate porphyria (step 7).
What are the steps to prepare M sulphuric acid?
To prepare 1 M sulfuric acid (H2SO4), you would need to dilute concentrated sulfuric acid to the desired molarity. Calculate the volume of concentrated sulfuric acid needed based on its concentration (typically around 18 M) and the final volume required. Always add acid to water slowly with stirring and proper safety equipment due to the exothermic nature of dilution and the corrosive properties of sulfuric acid. Dilute to the final volume with distilled water.
How many steps should you take in a day?
An adult should take 10,000 steps in a day. Though 10,000 steps for a child is too low. Remember that a journey of 10,000 steps starts with a single one.
What is the fullform of DCDA process for manufacturing of sulfuricacid?
The full form of DCDA process is Double Contact Double Absorption process for the manufacturing of sulfuric acid. In this process, the sulfur dioxide gas is reacted with air to form sulfur trioxide, which is then absorbed in water to produce sulfuric acid. The double contact and double absorption steps enhance the overall efficiency of the sulfuric acid production.
What steps should you take if you are a UScitizen marrying a Peru citizen?
What steps should you take if you are a UScitizen marrying a peru citizen?
What are the seven steps you should go through when you approach a roundabout?
What are the seven steps you should go through when you approach a roundabout?
What are seven steps you should go through when you approach a roundabout?
What are the seven steps you should go through when you approach a roundabout?
How many intermediate steps should a distribution chain have?
steps in distribution chain company
