0
Which surfactant should you use to add to sodium hypochlorite for mold stain removal from plywood?
A non-ionic surfactant is typically recommended for use with sodium hypochlorite for mold stain removal from plywood. Non-ionic surfactants are less likely to react with bleach and are effective at breaking down and removing stains without leaving residue behind. Be sure to follow manufacturer instructions and conduct a spot test before full application.
What else can I help you with?
What is the reaction of sodium hypo chlorite in water?
When sodium hypochlorite is added in water it simply ionizes into Na+ and ClO-, if these ions react with water the products should be NaOH and HClO , but they again react as acid base and form the same ions in water.
What happens if you mix calcium hypochlorite and carbon dioxide?
It forms calcium carbonate (CaCO3) and dichlorine monoxide (Cl2O).
How can Chloroform reaction performed by methanol?
Chloroform can be formed from methanol through a series of reactions involving sodium hypochlorite and sodium hydroxide. Methanol is first reacted with sodium hypochlorite to produce chloromethanol, which is then further reacted with sodium hydroxide to give chloroform as the final product. This process should be conducted under controlled conditions with proper safety measures due to the toxicity of chloroform.
What variable should be measured when removing oil form sand?
The variable to measure when removing oil from sand is the oil concentration remaining in the sand after the removal process. This can be quantified by analyzing the oil content in the sand before and after the removal process to assess the efficiency of the oil-removal method.
Can benzene be used for stain removal on hotel laundry?
No, benzene is a hazardous chemical that should not be used for stain removal on hotel laundry. It is a known carcinogen and poses serious health risks to individuals exposed to it. It is important to use safe and approved stain removal methods in commercial laundry facilities.
What is hyperchlorite?
It should be sodium hypochlorite: NaClO
How many hypochlorite should be used when rechlorinating a full water trailer?
22 hypochlorite ampules should be used when re-chlorinating a full water trailer.
Which thinset should be used over plywood?
The thin set you should use over plywood is called Durabond. Durabond is a water-based coating that dries to a hard, durable finish. It can be applied directly to new or old drywall and will not cause any harm if it comes in contact with insulation.
How many hypochlorite ampules should be used when rechlorinating a full water trailer?
22 hypochlorite ampules should be used when re-chlorinating a full water trailer.
What size plywood should be used for a subfloor?
For a subfloor, typically 3/4 inch thick plywood is recommended for stability and durability.
How thick should the plywood be under a mattress for optimal support and durability?
For optimal support and durability, the plywood under a mattress should be at least 3/4 inch thick.
How deep should a dado be in 3/4 plywood to ensure a secure and precise fit for the intended project?
A dado in 3/4 plywood should be approximately 1/4 to 1/3 of the thickness of the plywood for a secure and precise fit in the intended project.
What size pocket hole screws should be used for 1/2 inch plywood?
For 1/2 inch plywood, you should use 1 inch pocket hole screws.
Can you ingest sodium hypochlorite?
Not safely. Sodium hypochlorite is very alkaline, which on its own is enough to make it dangerous. Additionally, sodium hypochlorite will react with hydrochloric acid, which is in stomach acid, to produce chlorine gas, which is extremely toxic.
What size screws should be used for 1/2 inch plywood?
For 1/2 inch plywood, it is recommended to use 6 or 8 screws.
What thickness plywood should be used for a roof?
For a roof, plywood with a thickness of at least 5/8 inch is recommended to provide sufficient strength and support.
What type of router bit should I use to cut plywood effectively?
For cutting plywood effectively, use a straight router bit with a carbide cutting edge. This type of bit is ideal for clean and precise cuts in plywood.
