0
What else can I help you with?
What does 1 inch equal?
2.54cm
Can ceramic tile be installed over quarter-inch concrete backer board rather than half-inch if the underlayment is a three-quarter inch 7-layer flooring grade plywood?
You did not mention if the three-quarter inch stuff was T&G (tounge and grove), that might make a little difference. I am not an expert in this area but have some personal experiences to share. I was allways told from old school you should have two layers of half inch material one layer turned ninety degrees from the other to give a solid one inch floor. Then you could use the one quarter backerboard and end up with a good tile floor. Then the new school came along and told me i could use one quarter over the T&G three quarter. They said the three quarter T&G was equal to the old style one inch. I tried it with the three quarter and i have several grout cracks and two broken tiles. I was using one quarter quarry tiles six by six. Have now fixed yet but in another room i used three quarter T&G plus another one half inch plywood then one half inch backerboard and same tiles no cracks.
Minimum thickness of load bearing RCC wall?
7.5 inch
What is W9xW9 welde wire mesh?
W9xW9 welded wire mesh consists of lengths of steel wire welded into 9 inch by 9 inch squares. This material is used to reinforce concrete panels and floors.
What is the standard thickness for a lean concrete?
Standards normally are 4 inch AA
HOW TO CONVERT DECIMAL TO ARCHITECTURAL SCALE?
To convert a decimal measurement to an architectural scale, first determine the scale you are using (e.g., 1/4" = 1'). Next, multiply the decimal measurement by the scale factor (for example, if using a 1/4" scale, multiply by 48, since 1 foot equals 12 inches and there are 4 quarter inches in an inch). This will give you the corresponding length in inches on the architectural drawing. Finally, round as necessary to the nearest fraction commonly used in architectural drawings, such as 1/16" or 1/8".
How do you use a one twentieth of an inch equals one foot scale on an architectural drawing?
The scale would be 1:240
What is 0.160 of a inch?
0.160 of an inch is equivalent to 160 thousandths of an inch. In decimal form, this is slightly more than one-sixth of an inch. To convert it to millimeters, it is approximately 4.064 mm. This measurement is often used in various applications, including manufacturing and engineering.
If we convert the 1cm to inch what is the answer?
If we convert 1cm in inch the answer is 0.3937008
Convert diameter inch to linear inch?
An inch is an inch is an inch is an inch....
How do you convert an architectural scale measurement to an engineering scale measurement?
It's not too difficult once you see how its done. Let's take a look at some common arch. units converted to eng. units. when converting, remember, you do not have to convert the whole foot numbers. So youre just focused on converting the inches and fractions of an inch. So: 1" = 1"/12"= .08' (take your inches and divide them by 12") 2" = 2"/12" = .16' 3" = 3"/12" = .25' and so on. for fractions of an inch: 1/8" = (1/8)/12 = .01' (divide 1 by 8, and then divide that 12) 1/4" = (1/4)/12 = .02' 1/2" = (1/2)/12 = .04' and so on. For example, let's say you needed to convert 12' 5 1/2" to engineering units. It would be as follows: 12' is, well, 12' 5 1/2" can also be written as 5.5". So, 5.5"/12" = .4583 Therefore 12' 5 1/2" converts to 12.4583'.
How do you convert thousandths of an inch into an inch?
Mutiply by 1000
How do you measure a scale drawing and then find the dimensions of the actual object with the given scale?
To measure a scale drawing, use a ruler to determine the lengths of the drawn dimensions. Once you have those measurements, apply the scale factor provided (e.g., 1 inch = 5 feet) to convert the drawing dimensions to actual dimensions. Multiply the measured lengths by the scale factor to find the real-world dimensions of the object. For instance, if a line in the drawing measures 3 inches and the scale is 1 inch = 5 feet, the actual dimension would be 3 inches × 5 feet/inch = 15 feet.
What is the scale using a ruler of the distance between the distance from denver to Lincoln measure to the nearest 14 inch?
To measure the distance between Denver and Lincoln using a ruler with a scale of 1 inch = 100 miles, you would convert 100 miles to inches, which equals 1 inch on the ruler. Therefore, to measure to the nearest 1/4 inch on the ruler, you would calculate 1 inch divided by 4, which equals 25 miles for each 1/4 inch on the ruler.
How do you covert feet to 1 24 scale?
To convert feet to a 1:24 scale, first, convert the measurement in feet to inches since there are 12 inches in a foot. For example, if you have a measurement of 2 feet, multiply by 12 to get 24 inches. Then, divide that number by 24 to find the corresponding measurement in the 1:24 scale. In this case, 24 inches divided by 24 equals 1 inch in the model scale.
Which map has a smaller scale a map with one inch that equals one hundred miles or a map that has one inch equaling two hundred miles?
The smaller scale map is the 1 inch to 200 miles scale.
How does 11 inch convert cm?
1 inch = 2.54 cm. To convert inches to centimeters, multiply by 2.54.
