answersLogoWhite

0

Safety reasons, they not the strongest material to use, are they?

User Avatar

Wiki User

14y ago

What else can I help you with?

Continue Learning about Civil Engineering

A civil engineer chooses to use wooden beams because they will sag before they break. This is an example of?

Choosing a material that will show warning before it fails.


What vertical member are used to support girders and beams?

Vertical members are called posts. often they have braces on either side of the post to support the weight as well.


What is the use of cantilevers in construction?

: I would consider the most common use for cantilever beams to be in building construction.....and probably the most obvious example is in mediaeval buildings with a framework of oak beams . Everyone must have seen these old buildings where the upper stories are wider than the ground floor , very common in Europe . The ceiling beams for the ground floor (also the floor beams for the upstairs rooms)are arranged to project out through the walls by 10-18 inches (30-45cm) , and the wall structure for the upper stories is built apon the projecting ends . This allows a larger open space to be achieved in the ground floor rooms without annoying support pillars because the weight is partly offset by the weight of the upper stories acting as a counter balance . This technique has been described as a way to avoid the tax on the building 'footprint', but this is not true in all countries where it was adopted , the tax merely prompted a wider acceptance of the technique . The same building tricks are used on modern buildings and bridges , but are not always obvious or visible when the structure is completed .


What is beam bearing?

Beam bearing refers to the capacity of a structural beam to support loads without experiencing excessive deflection or failure. It is a critical design consideration in construction and engineering, ensuring that beams can safely carry the weight of the structures they support, including live loads (occupants and furniture) and dead loads (the weight of the beam itself and other permanent fixtures). Proper beam bearing is essential for maintaining the stability and integrity of buildings and other structures.


Wood or steel beam to support a roof ceiling or floor?

There are two criteria for making the decision. 1) How much weight is the beam carrying. Wood beams look great and can carry most residential loads. Commercial buildings often use steel beams to carry the snow wind and floor loads, but heavy timber can also do the trick. 2) How should the wood or steel beam look? If the building is prettier using wood, that might be the way to go. If steel looks better - use steel. Sometimes a combination of wood and steel is perfect.

Related Questions

Why are wooden beams jutting from the walls of Timbuktu's buildings?

The wooden beams jutting from the walls of Timbuktu's buildings serve both structural and aesthetic purposes. They are part of the traditional architectural style, helping to reinforce the adobe structures and providing support for upper levels and roofs. Additionally, these beams facilitate the construction of wooden scaffolding, which is essential for maintenance and repairs. Their presence also reflects the cultural heritage and historical significance of the region's architecture.


What are some examples of beams?

Examples of beams include I-beams, which are commonly used in construction for their strength and efficiency; cantilever beams, which extend beyond their support and are often found in balconies and overhangs; and T-beams, which are used in reinforced concrete structures. Additionally, wooden beams are prevalent in residential buildings, serving as support for roofs and floors. Each type of beam is designed to bear loads and resist bending in specific applications.


Are ther wooden beams in the pyramids?

ARE THER WOODEN BEAMS IIN THE PYRAMIDS FOR CONSTRUCTION


What kind of buildings did the ancient israelites have?

They were generally made of stones overlayed with mortar. Wooden beams held up the ceiling/roof.


What type of roofs did Egypt have?

The buildings had wooden beams and were covered with rushes or mats. This is one reason in ancient ruins that there are no roofs, but only walls left.


What does trussed mean?

Trussed means a rigid framework, as of wooden beams or metal bars, designed to support a structure, such as a roof.


Where is the rope in Herbert's lair on misson 6 club penguin?

The rope is on the wooden beams. The wooden beams are to the right of the door. They are right next to jerry can and table.


How is iron ore useful?

Iron ore was traditionally used to make metal poles. These metal poles would be used as support beams in buildings for example.


What were Inca houses made of?

Inca homes and buildings were made out of fieldstones and dirt. The roofs were primarily made of wooden beams and thatch.


Where are the studs located in a wall?

Studs are vertical wooden or metal beams that support the structure of a wall. They are typically spaced 16 or 24 inches apart and run from the floor to the ceiling.


Which is the clearest example of cause and effect in The City Without Us?

Without daily pumping, Manhattan's subway tunnels would be flooded or If flooding were to go unchecked, steel support beams in buildings would rust. or Unheated buildings would result in a destructive freeze-thaw cycle.


When old bulidings fall what are done with the old wooden beams?

Often they are sold as reclaimed material and then reused as beams or cut up into flooring.