answersLogoWhite

0

First off you have to know what kind of pump it has...ie.. a rotary, where the fuel lines are in a circle out the back of it or an in-line where the fuel lines come out the top.

User Avatar

Wiki User

14y ago

What else can I help you with?

Related Questions

How much petrol or diesel can be filled at a time in a scooter car tractor?

tractor8.6


How much diesel can be filled at a time in tractor?

As much as the fuel tank can hold


What is book time on replacing a water pump on a sterling tractor?

This will depend on:Engine fittedAccessories on the engineYear


Where is the hydraulic fluid cap on a case 1190 tractor?

Well, friend, finding the hydraulic fluid cap on your Case 1190 tractor is like finding a happy little tree in a meadow. It's usually located near the back of the tractor, close to the hydraulic pump. Take a gentle stroll around the tractor and you'll spot it in no time. Just remember, there are no mistakes, only happy accidents in finding that cap.


How do you time a Mazda B2500 diesel injector pump?

you need a dial gauge which screws into the back of the pump its pretty simple after that.


How do you time a injector pump on a b7800 Kubota tractor?

To time the injector pump on a Kubota B7800 tractor, first ensure the engine is at top dead center (TDC) on the compression stroke for the first cylinder. Then, remove the injector pump's timing cover and align the timing marks on the pump and the engine. Adjust the pump position as necessary to align these marks, and then secure the pump in place. Finally, reassemble any removed components and test the engine to ensure proper operation.


How do you time the injection pump on a ford 9600 tractor?

To time the injection pump on a Ford 9600 tractor, start by ensuring the engine is at top dead center (TDC) on the compression stroke for cylinder number one. Remove the injection pump cover and align the timing mark on the pump with the timing mark on the engine. If applicable, use a dial gauge to check the plunger lift, adjusting the pump as necessary. Finally, secure all components and recheck the timing before reassembling.


What is john deere's most expensive tractor?

Currently the largest Deere tractor in mass production is the 9630 articulated or tracked tractor with a 13.5 litre John Deere diesel engine producing more than 500 HP th Currently the largest Deere tractor in mass production is the 9630 articulated or tracked tractor with a 13.5 litre John Deere diesel engine producing more than 500 HP through a multi speed powershift transmission


Run your of diesel on combi van how do you get it to run again?

Did I get it right, you have run your diesel engine out of fuel? If I did here is what you do. It is best to have help, a friend or relative.You must bleed the injectors Usually there is a plunger type pump on the fuel pump to pump in the diesel. Loosen off all injectors and pump by hand whilst operating starter. When she fires diesel will start to squirt from loose injectors, tighten them down one at a time. the hand pump often will not build enough pressure to start it. In which case you must pressurise the tank using a compressor. Hold a rag around the air hose to block escaping air and hold in place with compressor running and go through the whole process again. Don't feel bad, we have all done it, but only a fool would run out of fuel in a diesel twice.


How do you time a john deere engine oil pump on a 2010 tractor?

To time a John Deere engine oil pump on a 2010 tractor, first ensure the engine is at top dead center (TDC) on the compression stroke of the number one cylinder. Remove the oil pump cover and align the timing mark on the oil pump with the corresponding mark on the engine block. After adjusting the pump, reassemble the cover, ensuring all bolts are properly torqued. Finally, check for proper oil pressure after starting the engine.


How do you time the diesel pump for the 66L engine?

To time the diesel pump for a 66L engine, first, ensure that the engine is at top dead center (TDC) on the compression stroke for the first cylinder. Next, align the timing marks on the pump drive and the engine to ensure proper synchronization. Adjust the pump's position as necessary to match these marks, and then securely fasten the pump in place. Finally, double-check the timing by cranking the engine to confirm proper operation.


Why tractor tires are big?

In the case or semi tractor trailer; it was to add more surface area in order to spread out the weight per square inch on the ground. In the case of farm tractor tires; it is like a semi in the weight part so it does not compact the ground and at the same time it gives more area for traction, and for the height, that is for ground clearance also.