0
48,000 lbs of payload, or 48,000 lbs gross weight (vehicle + payload)?
For 48,000 lbs. of payload, some five axle combinations can haul that legally, although that is cutting it a bit close. We're talking a fairly short wheelbase tractor, and aluminum flatbed with ten foot spread axle (spread axles can have a total of 40,000 lbs, vs. 34,000 lbs for tandem axles). If it pushes your total vehicle weight over 80,000 lbs, then you'll need an oversize permit, even with a five axle setup.
As for 48,000 gross vehicle weight, any tandem axle straight truck would do.
What else can I help you with?
How many horsepower to produce 48000 kilowatts?
To convert kilowatts to horsepower, you can use the formula: 1 kilowatt = 1.34102 horsepower. Therefore, to produce 48000 kilowatts, you would need 48000 x 1.34102 = 64314.96 horsepower.
What is the least number that can be rounded off to 48000?
To find the least number that can be rounded off to 48000, we need to consider the midpoint between 48000 and 47999.5, which is 47999.75. Rounding up this number gives us 48000. Therefore, the least number that can be rounded off to 48000 is 47999.75.
What is the right air pressure on the tag axle of cement truck loaded with 9yds?
For any truck, it is supposed to be such that all axles of the group hold a similar amount of load to achieve an evenly distributed load. You need to use scales at floor level to measure the load values depending on the air pressure.
How do you properly load a 53 ft. Dryvan simi touch trailer?
Front to back... unlike open deck trailers (flatbeds, RGNs, etc), van trailers typically have sliding tandems to balance out the load and adjust load distribution over the trailer and drive axles. Anything more specific, and we'd need to have an idea of what the commodity is.
How many axles do you need for a bmx bike?
Five. One for each wheel, one for the cranks and one for each pedal.
How many tons does a ten wheeler hold?
tons a 10 wheeler will hold depends on the configuration of the truck. a lot has to do with the distance of the axles from each other. when loading a truck to get correct weight the load is distributed to get proper weight over axles. but benerally a 10 wheeler is only tagged to gross 54 ooo pounds. so with that you need to subtract the weight of the empty truck to find out what the actual payload will be
Can bike pegs go on any bike?
No. At the very least you need a bike with solid, nutted axles.
How do you convert tandem loads to triaxle loads?
To convert tandem loads to triaxle loads, you need to assess the total weight supported by the tandem axles and then distribute that weight across the three axles of the triaxle configuration. Generally, a triaxle can support more weight due to its additional axle, allowing for better weight distribution and reduced stress on each axle. You may also need to refer to specific load distribution guidelines or regulations applicable to your region, as they can vary. Overall, the conversion involves ensuring that the total load does not exceed the legal limits for triaxles.
What is the toll cost for a truck to go from Annville PA to Kearny NJ?
You will need to contact each state for the toll amounts. For trucks the toll is reliant on the number of axles. The usual truck/tractor has 3 axles and a trailer will also have two axles so the rate would be for 5 axles.
Why are there single axle semis and dual axle semis?
The amount of weight they'll carry on those axles dictates whether or not they need single or tandem axles.
What causes axles to break on a Dodge Intrepid?
you may have a transmission problem. See the axles will break to save the transmission from damage. Or you might need to change the bushings on the suspension.
What size socket do you need to change the wheel bearings on 1998 GMC Jimmy front and back axles?
Need to know if 2 wheel or 4 wheel drive for the front. Either way, there is no nut on the back axles.
