0
What else can I help you with?
Is TCP a half duplex or ful duplex protocol?
TCP is usually used as full duplex, but in some case, half duplex can also be used in TCP.
What are attributes possessed by engineers?
They are very practical. If you had a glass half filled with water, an optimist would say it was half full, a pessimist would say it was half empty but and engineer would observe that the glass was twice as big as it needed to be.
What are the three types of data flow?
the three types of data flow are: simplex,half duplex and full duplex
Which layer of the osi model determines whether the communications between nodes will be full or half duplex?
session layer
What is the different steps in bisecting a line?
1. first draw a line any measurements 2. then get your compass and place it on the left side of your line remembering that the compass has to be more than halfway open then go up to the middle with ur compass and draw one half of a cross with the compass then draw another half a cross below the line not changing the width of the compass but make sure it is in line with the other half cross now take the compass of your page now place the point on the other side of the line and do the same as i just said then you should get two crosses one above the line and one below the finishing touch is get a ruler and where the crosses meet draw a line strainght the way down and then your done i hope that helped i learnt it in a maths lesson
What is a full subtractor?
A half-subtractor lets you borrow out, but not borrow in. A full subtractor is made by combining two half-subtractor and adding an OR-gate. (lets you both BOR_in as well)
What are advantages and disadvantages of full subtractor?
Advantage:1:To overcome half subtractor, full subtractor comes into play
What are the advantages of full subtractor over half subtractor?
-Half subtractor is used to reduce the force of audio or radio signals. -It can be used in amplifiers to reduce the sound distortion. -Half subtractor is used in ALU of processor. -It can be used to increase and decrease operators and also calculates the addresses.
Full subtractor using 2 half subtractor?
The half adder is an example of a simple, functional digital circuit built from two logic gates. A half adder adds two one-bit binary numbers A and B. It has two outputs, S and C (the value theoretically carried on to the next addition); the final sum is 2C + S.
What is the difference between half subtractor and full subtractor?
simply by complementing x input before applying to and gate for generating carry
Half-Subtractor circuit using NOR gates?
By using 5 NOR gates, we can implements half-subtractor. The inputs for 1st NOR gate are A and B, for 2nd NOR gate inputs are the output of 1st NOR gate and A input, for 3rd NOR gate inputs are the output of 1st NOR gate and B input, for 4th NOR gate the inputs are gates 2 and 3, and for last gate input is the output of the 4th gate.
What are applications of subtractor circuit?
The optical signal processing is one of the application of the half subtractor circuit. Binary numbers is another application.
What is the logic circuit for a full adder using only NAND gate?
by the procedure design a half subtractor design a logic ciruit to add two numbers with five bits each drawthe logic diagram of afull adder using using NAND gates only ?
What are subtractor op-amplifier?
Subtractor :In Electronics Subtractor is a Combinatorial circuit which is used to Subtract two Binary Numbers, x & y.Half Subtractor :Half Subtractor is a circuit which is used to Subtract the two bit Binary Numbers.Full Subtractor :Full Subtractor is a circuit which is used to Subtract the Two Bit Binary Numbers and a 1 borrowed from Last Lower significant stage.Hope this answer will help you.....Remember In your Prayers.
If a man draw half a liter oil from a twenty liter drum which is exactly half full what percentage of the content of the drum does he draw?
5%=one twentieth
What effect does a negative result have on the outputs in the half subtractor?
In a half subtractor, a negative result occurs when the minuend (the first input) is less than the subtrahend (the second input). This situation is typically represented in binary arithmetic by borrowing, which affects the outputs. The half subtractor will output a '0' for the difference when the minuend is less than the subtrahend, while the borrow output will be '1' to indicate that a borrowing operation is necessary. Thus, a negative result signifies that the subtraction cannot be performed without adjusting for borrowing.
How can draw the circuit diagram if input more than 3 using full or half adder?
You'll need to go to a website that does graphics - it's too complicated to describe in text-only.
