How do you assemble and disassemble a computer step by step?

Answer 1

1. Just unassemble the plastic part of the back by holding and dragging it in the right way :

[ Plastic Part >>> ] >>>> (to the right)

Be careful not to broke the pins.

2. Move out the top by dragging it out.

From the side it looks like this :

|_[ | | | | >>>>>>]

Drag it >> this way

And you'll found the front part shares the platform with the main body.

Answer 2

To start with you want to disconnect all the leads from the back of the computer.

Then at the back of the computer there should be 1-2 screws on the side of the panel, unscrew these and then slide or lift off the side panel.

Inside disconnect the wires and go from there. Any trouble try PC world, maplins or you tube for videos on how do go from here.

Signed,

Hungry Hacker

I found this website for you, I ! :)

http://www.instructables.com/id/Disassemble-a-Computer/

Answer 3

1st : Wake up.

2nd : Go to Hardware store.

3rd : Buy Hammer.

4rd : Go back to your home.

5th : Look for your CPU Case.

6th : Destroy it using your hammer.

7th : Works Like a charm ! :D

Answer 4

Depending on the model of computer, there are many different ways of doing this..

However on a Dell computer it is very rare that you will need to use a screwdriver to open the outer casing, look on the dell website for the service manual.

Answer 5

To disassemble a computer you must first make sure the computer is completely shut off and unplugged from everything. Then push the power button a few times to drain the power out of the board.

WARNING: NOT USING THE RIGHT TOOLS WILL CAUSE PERMINENT DAMAGE TO A COMPUTER!!!!!

1. In the rear of the PC there will either be a release lever or screws to take the covers off. Do what is necessary to remove the side panels.

2. You will needto wear ananti-static wrist band and have an anti-staticmat grounded and connected properly. Without these you can transfer your static to the motherboard and cause permanent damage!

3. Locate the motherboard battery, This usually looks like a large silver quarter sized disc held in by clips or springs, Once located remove the battery!

4. Disconnect all wires from the motherboard leading to the power supply, switches, hard drives, CD/DVD/Blue-ray/Floppy drives, front USB and fan cables.

ALL parts should be placed on the anti-static mat!!!

5. Remove all PCI, PCI-E and any other slotted removable cards or adaptors.

6. Locate the mounting screws for the hard drive(s) and other removable devices and remove them from the computer.

Note! some computers have a release or separate set of screws for the docking bays that you may have to remove first in order to remove the devices..

7. Locate and removethe screws on the power supply on the rear of the computer and the PCI slot covers and remove the power supply from inside the computer.

8. Locate the screws from the motherboard and remove them carefully, remove the motherboard stand offs as well, then remove the motherboard.

To reassemble just follow the steps in reverse order.

To start with you want to disconnect all the leads from the back of the computer.

Then at the back of the computer there should be 1-2 screws on the side of the panel, unscrew these and then slide or lift off the side panel.

Inside disconnect the wires and go from there. Any trouble try PC world, maplins or you tube for videos on how do go from here.

It all depends on how far you need to assemble or disassemble a computer.
Assembly:- First placed your mother in the casing, and then placed other hardware. After build all hardware then connects the wires of Power supply.

Answer 6

how to disassembly Samsung sens pro 520 notebook

Answer 7

Unscrew the screws on the back and take the cover off. Beware that certain parts of the monitor contain dangerous amounts of electricity for hours after you unplug it.

Answer 8

Use the the indications from the leaflet attached to box.